User manual SHERWOOD NEWCASTLE R-865

[. . . ] R-865 Audio/Video Receiver Introduction READ THIS BEFORE OPERATING YOUR UNIT ENGLISH This symbol is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING : TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. Note to CATV System Installer : This reminder is provided to call the CATV system installer's attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as pracitcal. FCC INFORMATION This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. [. . . ] · Depending on the speaker settings and the number of the encoded channels, etc. the sound from the corresponding channels cannot be reproduced. (For details, refer to "SETTING THE SPEAKER SETUP" on page 49. ) Channels FRONT L/R CENTER SURROUND L/R SURROUND BACK L/R SUBWOOFER 33 ENGLISH ENJOYING SURROUND SOUND · Surround sound effect will not work properly if the signal passes through a graphic equalizer. Please refer to your equalizer operating instructions for guidance on switching off (or defeating) the equalizer. Note: · Before surround playback, first perform the SPEAKER SETUP procedure, etc. on the OSD menu for optimum performance. (For details, refer to "SETTING THE SPEAKER SETUP" on page 49. ) Depending on the input digital signal format, select the desired decoding mode. ENGLISH 1 or · You can select the "DTS", "DOLBY DIGITAL", "MPEG" or "PCM" mode directly on the remote control. · Each time the DECODING MODE button is pressed, the decoding mode changes as follows : * Auto mode("AUTO" lights up): The input digital signal format (DTS, Dolby Digital, MPEG or PCM( 2 channel stereo), etc. ) used by the selected digital input source is detected automatically to perform the necessary decoding process for optimum surround mode. * Dolby Digital mode("DOLBY DIGITAL" lights up): The Dolby Digital signal processing is performed only when Dolby Digital signals are input. * DTS mode(" DTS" lights up): The DTS signal processing is performed only when DTS signals are input. * MPEG mode("MPEG" lights up): The MPEG signal processing is performed only when MPEG signals are input. * PCM mode("PCM" lights up): The PCM signal processing is performed only when PCM signals are input. Notes : · Only when the digital input is selected as signal input for the input sources except TUNER and TAPE MONITOR, the decoding mode can be selected. · Noise may be generated at the beginning of playback and while searching during DTS playback in the auto mode. In this case, try playing in the DTS mode. Select the desired surround mode. 2 · Each time the MULTI CONTROL knob is rotated or the DSP MODE UP(>) or DOWN(<) button is pressed , the surround mode changes depending on the input signal format and the selected decoding mode as follows : Signal format being input Dolby Digital 5. 1, Dolby Digital EX 6. 1 channel sources Dolby Digital 2 channel sources DTS sources DTS 96/24 sources MPEG sources PCM ( 2 channel ) sources Analog stereo sources Selected decoding mode Auto, Dolby Digital mode or Auto, DTS mode Auto, MPEG mode Auto, PCM mode - Selectable surround mode (DOLBY DIGITAL EX, ) DOLBY DIGITAL (DOLBY DIGITAL EX, ) DOLBY DIGITAL, PL II MOVIE, PL II MUSIC (DTS ES MATRIX or DTS ES DISCRETE, ) DTS DTS 96/24 MPEG PL II MOVIE, PL II MUSIC, BYPASS, DTS NEO 6 : CINEMA, DTS NEO 6 : MUSIC, THEATER, MOVIE, HALL 1/2, STADIUM, CHURCH, CLUB 1/2, ARENA 1/2, GAME, 4CH STEREO, MATRIX ( ): Possible only when surround back channel is not set to "None". (Refer to "When selecting the SPEAKER CONFIGURATION" on page 49. ) BYPASS mode: Audio signals bypass signal processing circuits for surround sound and are played in stereo mode. If Dolby Pro Logic IIx, Dolby Virtual Speaker or Dolby Headphone mode is combined with BYPASS mode, you will enjoy its original surround effects, not affected by other surround modes. · When MPEG signals are input in the required decoding mode, the corresponding surround mode will be automatically selected regardless of using the MULTI CONTROL knob or DSP MODE UP(>) or DOWN(<) button. Notes: · When the selected decoding mode is not matched to the input signal format, the indicator of the signal being input flickers, meaning the required process cannot be performed and no sound is heard. Therefore, be sure to select the required decoding mode and the available surround mode according to the input signal format. · When the 8 CH DIRECT is selected as an input source, the decoding and surround modes cannot be selected. · When the pure audio function is activated, the surround mode cannot be selected. · When 96 kHz PCM signals are input, only the stereo mode can be selected. · When DTS 96/24 or MPEG signals are input, the Dolby Pro Logic IIx, Dolby Virtual Speaker and Dolby Headphone modes cannot be selected. 34 Continued When canceling the surround mode for normal stereo operation. · Depending on the signal format which is being input, either the stereo mode or the 2CH downmix mode is selected. [. . . ] · Select the desired center speaker setting. · Adjust master volume and center level. · Under the proper situations, perform the 7. 1(or 6. 1) surround playback. (For details, refer to "ENJOYING SURROUND SOUND" on page 34. ) · Assign the power amplifier to the surround back channels. (For details, refer to "SETTING THE POWER AMP ASSIGN" on page 49. ) · Adjust master volume and surround back level. · Select the desired surround back speaker setting. [. . . ]