User manual SHERWOOD P-965

[. . . ] P-965 A/V Tuner Pre Amplifier Introduction READ THIS BEFORE OPERATING YOUR UNIT ENGLISH This symbol is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING : TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. Note to CATV System Installer : This reminder is provided to call the CATV system installer's attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as pracitcal. FCC INFORMATION This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. [. . . ] · Each time this button is pressed, the corresponding channel is selected as follows: STANDBY POWER ON FRONT-L FRONT-C FRONT-R SURR-R SUBWOOFER PAGE SURR-L ( SURR-C) or ( BACK-L BACK-R) MAIN FAV CH. SEL or DECODE DSP DSP RETURN STEREO 1 4 7 DISP 2 5 8 0 M2 3 6 9 OSD/MENU ENT MI M3 RNC-510 · Depending on the speaker settings and surround mode, etc. , some channels cannot be selected. · ( ): possible depending on whether the surround back channel is set to 2 CH or 1 CH. Note: When speakers are switched off, only FRONT-L and FRONT-R channels can be selected. 32 2 Adjust the level of the selected channel as desired. STANDBY POWER ON 3 Repeat the above steps each channel level. and to adjust PAGE MAIN FAV CH. SET VOL CH/ ADJUST or DOWN UP MUTE CH/ ADJUST DECODE DSP DSP RETURN STEREO 1 4 7 DISP 2 5 8 0 M2 3 6 9 OSD/MENU ENT MI M3 RNC-510 Adjusting the Dolby Pro Logic IIx / Dolby Pro Logic II Music parameters · When selecting either the Dolby Pro Logic IIx Music mode or the Dolby Pro Logic II Music mode depending on whether "S/B CH" is set to "None" or not, you can adjust the various surround parameters for optimum surround effect. (Refer to "When selecting the SPEAKER CONFIGURATION" on page 44. ) · In case of PL IIx MUSIC mode, only when original surround mode is "BYPASS" mode or 2 channel digital signals from Dolby Digital sources, etc. are input, these parameter settings affect the surround effects. 1 Press the DOLBY PL II MUSIC PARAMETER button to select the desired parameter. · Each time this button is pressed, the parameter changes and is displayed for several seconds as follows; Panorama mode("PANORAMA", default value : OFF) This mode extends the front stereo image to include the surround speakers for an exciting "wraparound" effect with side wall imaging. Select "OFF" or "ON". Center width control("C-WIDTH", default value : 0) This adjusts the center image so it may be heard only from the center speaker, only from the left/right speakers as a phantom image, or from all three front speakers to varying degrees. The control can be set in 8 steps from 0 to 7. Dimension control("DIMENSION", default value : 0) This gradually adjusts the soundfield either towards the front or towards the rear. The control can be set in 7 steps from -3 to +3. STANDBY POWER ON AUD2 SLEEP DIMM D/A S. A/B SUR. B PURE or ROOM2 T. TON OSD PARA. PAGE1 At the desired parameter, adjust it as desired. 2 or 3 Repeat the above steps adjust other parameters. and to STANDBY POWER ON PAGE MAIN FAV CH. SET VOL MUTE CH/ ADJUST CH/ ADJUST DECODE DSP DSP RETURN STEREO 1 4 7 DISP 2 5 8 0 M2 3 6 9 OSD/MENU ENT MI M3 RNC-510 · If the parameter display disappears, start from the step again. 33 ENGLISH LISTENING TO RADIO BROADCASTS ENGLISH Auto tuning Select the desired band. 1 Select the tuner. 2 STANDBY POWER ON AUD1 TUNER CD VID1 VID2 VID3 VID4 VID5 BAND FREQUENCY or T. MON AUX PHONO PAGE1 · Each time this button is pressed, the band is changed to FM or AM. · When pressing the BAND button without selecting the TUNER, the tuner will be selected automatically. Press the TUNING UP(+) or DOWN(-) button for more than 0. 5 second. 3 + or STANDBY POWER ON AUD2 SCH. M PTY S MEMO TUNE+ E. TA E. PTY P. SCA PSET+ TUNE- PSETPAGE2 · Then " AUTO" appears on the display. The tuner will now search until a station of sufficient strength has been found. The display shows the tuned frequency and "TUNED". · If the station found is not the desired one, simply repeat this operation. · Weak stations are skipped during auto tuning. Manual tuning · Manual tuning is useful when you already know the frequency of the desired transmitter. · Perform the steps ~ in "Auto tuning" procedure and press the TUNING UP(+) or DOWN(-) button repeatedly until the right frequency has been reached. + or STANDBY POWER ON AUD2 SCH. M PTY S MEMO TUNE+ E. TA E. PTY P. SCA PSET+ TUNE- PSETPAGE2 Auto presetting · Auto presetting function automatically searches for FM stations only and store them in the memory. · While listening to radio broadcasts, press and hold down the (ENTER/)MEMORY button for more than 3 seconds. · Then "AUTO" lights up and this unit starts auto presetting. [. . . ] · Select the desired center speaker setting. · Adjust master volume and center level. · Under the proper situations, perform the 7. 1(or 6. 1) surround playback. (For details, refer to "ENJOYING SURROUND SOUND" on page 29. ) · Adjust master volume and surround back level. · Select the desired surround back speaker setting. [. . . ]