User manual SHERWOOD RD-6105

[. . . ] Introduction UNPACKING ENGLISH Congratulations on Your Purchase! Your new high fidelity receiver is designed to deliver maximum enjoyment and years of trouble free service. Please take a few moments to read this manual thoroughly. It will explain the features and operation of your unit and help ensure a trouble free installation. We recommend that you save the carton and packing material. [. . . ] Notes: · When the selected decoding mode is not matched to the input signal format, no sound is heard. Therefore, be sure to select the required decoding mode and the available surround mode according to the input signal format. · When the 6 CH DIRECT is selected as an input source, the decoding and surround modes cannot be selected. 15 When canceling the surround mode for stereo operation. ENGLISH · Then the stereo mode is selected. · To cancel the stereo mode, select the desired surround mode with using the DSP MODE button. Adjusting the Dolby Pro Logic II parameters · When selecting the Dolby Pro Logic II Music and Custom modes, you can adjust the various surround parameters for optimum surround effect. While scrolling "PL II MUSIC"(for Dolby Pro Logic II Music mode) or "PL II CUSTOM"(for Dolby Pro Logic II Custom mode), press the MEMORY/ENTER button to select the desired parameter. 3 · Each time this button is pressed, the parameter changes and is displayed for 5 seconds as follows: Panorama mode("PANO") : This mode extends the front stereo image to include the surround speakers for an exciting "wraparound"effect with side wall imaging. Select "OFF" or "ON". Center width control("C-WID") : This control adjusts the center image so it may be heard only from the center speaker, only from the left/right speakers as a phantom image, or from all three front speakers to varying degrees. The control can be set in 8 steps from 0 to 7. Dimension control("DIMEN") : This control gradually adjusts the soundfield either towards the front or towards the rear. The control can be set in 7 steps from - 4 to +2. 7 kHz Low Pass Filter("LPF") : Select "OFF" or "ON" to turn off or on the pass filter on the surround channels. Shelf Filter("SH - F") : Select "OFF" or "ON" to turn off or on the shelf filter on the surround channels. Right Surround Channel Polarity Inversion("PO - I") : Select "OFF" or "ON" to turn off or on the polarity inversion. Automatic Balancing("BAL") : Select " OFF" or "ON" to turn off or on the automatic balancing · If the Dolby Pro Logic II Music or Custom display disappears, you cannot select the parameter. In this case, select the desired surround mode again by pressing the DSP MODE button. · In the Dolby Pro Logic II Music mode, you cannot select the 7 kHz Low Pass Filter, Shelf Filter, Right Surround Channel Polarity Inversion and Automatic Balancing. · For your reference, the initial settings for parameters are as follows: "PANO" : "OFF", "C-WID" : "0", "DIMEN" : "0", "LPF" : "OFF", "SH-F" : "OFF", "PO-I" : "ON", "BAL" : "OFF". At the desired parameter, adjust it as desired. 4 · If the parameter display disappears, start from the step 3 again. 5 Repeat the above steps 3 and 4 to adjust other parameters. Note: · In the Dolby Pro Logic II Customer mode, you cannot set both of the 7 kHz Low Pass Filter and Shelf Filter to ON simultaneously. If so, the filter set previously is automatically changed to OFF. 16 Adjusting the speaker settings · Adjust the settings of front, center , rear speakers and subwoofer connected. · If the speaker setting is adjusted to "S", the low range bass sound of the channel(s) is redirected to the subwoofer or the front channels and if the speaker setting is adjusted to "N", the sound of the channel(s) is redirected to other channels. Press the SPEAKER MODE button for more than 2 seconds to enter the frontcenter-rear speaker mode. Select the desired speaker setting. · Each time this button is pressed, one of 11 different speaker settings is selected and displayed for 8 seconds as follows; FL-CS-RS, FL-CL-RS, FL-CL-RL, FL-CL-RN, FL-CS-RL, FL-CN-RL, FL-CS-RN, FL-CN-RS, FS-CS-RS, FS-CS-RN and FS-CN-RS 6 · The front-center-rear speaker setting is displayed. · When the SPEAKER button is set to off or the 6 CH DIRECT is selected as an input source, the speaker mode function cannot be available. [. . . ] 10 dB · Surround mode, only channel driven Front power output, 6 , 1 kHz, THD 0. 7 % . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125 W+125 W Center power output, 6 , 1 kHz, THD 0. 7 % . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125 W Rear power output, 6 , 1 kHz, THD 0. 7 % . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125 W+125 W DIGITAL AUDIO SECTION · Sampling frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]