User manual SHERWOOD RD-6108

[. . . ] OPERATINGINSTRUCTIONS AUDIO/VIDEO RECEIVER RD-6108 MASTER VOLUME MAIN POWER REMOTE SENSOR ST TUNED TAPE M PRESET MEM TONE DIRECT dB kHz MHz DTS ON/ OFF DIGITAL Pro Logic THEATER HALL ms SLEEP STANDBY INPUT SELECTOR AUDIO VIDEO TAPE MON. 6CH DIRECT AUTO SURROUND MODE DSP MODE STEREO DIGITAL INPUTS TONE DIRECT ON/STANDBY PHONES SPEAKER VIDEO 3 CHANNEL SELECTOR ADJUST TONE MODE SPEAKER MODE DYNAMIC RANGE CINEMA EQ MEMO/ENTER TUNING/PRESET T/P MODE FM MODE BAND ON/OFF VIDEO L - AUDIO - R RD-6108 AUDIO/VIDEO RECEIVER Introduction UNPACKING AND INSTALLATION ENGLISH Congratulations on Your Purchase! Your new high fidelity receiver is designed to deliver maximum enjoyment and years of trouble free service. Please take a few moments to read this manual thoroughly. It will explain the features and operation of your unit and help ensure a trouble free installation. [. . . ] The optimum delay time will be different according to the room size and the acoustic properties. It is recommended that you try several times to obtain the best effect. It is adjustable in Dolby Digital, Dolby Pro Logic II, Dolby Pro Logic or Dolby Virtual modes. (For details, refer to "In Dolby Digital, Dolby Pro Logic II, Dolby Pro Logic or Dolby Virtual mode, adjusting delay times of the speakers" on page 18) Speaker placement To obtain the best surround sound effect in your home, place the speakers as follows; Front speakers: Place each front speaker about 1m (40 ) from the TV set. Center speaker: Place the center speaker either above or below the TV set to assure good visualization of center channel program. Rear speakers: Place the rear speakers approximately 1m above the ear level of a seated listener on the direct left and right of them or slightly behind. Subwoofer: Reproduces powerful deep bass sounds. Place a powered subwoofer anywhere in the front as desired. The ideal surround system needs all the speakers listed above. To obtain the best surround effects, the speakers except the subwoofer should be full range speakers. Note: To avoid interference with the TV picture, use only magnetically shielded center and front speakers. For your reference, the sound from each channel can be reproduced according to the surround modes as follows: Channels Front L/R Center Rear L/R Subwoofer Modes DTS Dolby Digital Dolby Pro Logic II Dolby Pro Logic Dolby Virtual FRONT LEFT SUB WOOFER TV set CENTER SPEAKER FRONT RIGHT REAR LEFT REAR RIGHT Other Surround Stereo 6 CH DIRECT · Depending on the speaker settings, the sound from the corresponding channels cannot be reproduced. (For details, refer to "Adjusting the speaker settings" on page 16. ) 14 ENJOYING SURROUND SOUND ENGLISH Surround sound effect will not work properly if the signal passes through a graphic equalizer. Please refer to your equalizer operating instructions for guidance on switching off (or defeating) the equalizer. Depending on the input digital signal format, select the desired decoding mode. POWER DISPLAY SLEEP VIDEO1 1 When canceling the surround mode for stereo operation. 1 2 3 VIDEO2 AUTO STEREO 4 5 6 VIDEO3 7 8 9 CD T. TONE 0 P. SCAN TUNER AUTO DSP MODE D. TIME ADJUST AUX AUTO CH. LEVEL MASTER VOLUME REMOTE CONTROL UNIT RM-105 · Each time the AUTO button is pressed, the decoding mode changes as follows: IN-AUTO : The input digital signal format(DTS, Dolby Digital or PCM(2 channel stereo), etc. ) used by the selected digital input source is detected automatically to perform the necessary decoding process for optimum surround modes. IN-DTS : The DTS signal processing is performed only when DTS signals are input. IN-PCM : The PCM signal processing is performed only when PCM signals are input. Notes: · Only when the digital input is selected as signal input for the input sources except TUNER, AUX and TAPE MONITOR, the decoding mode can be selected. · Noise may be generated at the beginning of playback and while searching during DTS playback in the IN-AUTO mode. In this case, try playing in the IN-DTS mode. Select the desired surround mode. · Then the stereo mode is selected. · To cancel the stereo mode, select the desired surround mode with using the DSP MODE button. Adjusting the Dolby Pro Logic II parameters · When selecting the Dolby Pro Logic II Music and Custom modes, you can adjust the various surround parameters for optimum surround effect. [. . . ] 10 dB Surround mode, only channel driven Front power output, 6 , 1 kHz, THD 0. 7 % . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125 W+125 W Center power output, 6 , 1 kHz, THD 0. 7 % . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125 W Rear power output, 6 , 1 kHz, THD 0. 7 % . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125 W+125 W ENGLISH DIGITAL AUDIO SECTION Sampling frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]