User manual SHERWOOD RX-5502

[. . . ] RX-5502(A)2007. 5. 179:15AM 1 RX-5502(A)2007. 5. 179:15AM 1 RX-5502(A)2007. 5. 179:15AM 2 SAFETY INSTRUCTIONS 1. Read Instructions - All the safety and operating instructions should be read before the product is operated. Retain instructions - The safety and operating instructions should be retained for future reference. Heed Warnings - All warnings on the product and in the operating instructions should be adhered to. [. . . ] MUTE BUTTON Each time this button is pressed, the speakers are switched on or off as follows : ~ C/D ~ - / - ~ C/ - ~ - /D or (R2 C/D) or (R2 -/-) or (R2 C/-) or (R2 -/D) ( ) : When the ROOM2 mode is set to on. Press this button to temporarily mute the sound. Press it again to resume the previous sound level. 20. BAND (TUNER) BUTTON Each time the BAND (TUNER) button is pressed, the band changes as follows: FM ST FM MONO AM 9. INPUT SELECTOR BUTTONS Press this button to activate the sleep timer for a specified period of time. · Each time this button is pressed, the sleep time changes as follows: 10 20 30 90 OFF Unit : minutes 21. DIMMER BUTTON Press the button to select the desired input source. 10. ROOM2 BUTTON Press this button to enter the ROOM2 mode. 11. TONE DIRECT BUTTON Press this button to listen to a program source without the tone effect. 12. TONE BUTTON Press this button to select the brightness of the fluorescent display as desired. · Each time this button is pressed, the brightness of the fluorescent display changes as follows: ON dimmer OFF 22. REMOTE SENSOR When adjusting the tone (bass and treble), press this button to select the desired tone mode. · Each time this button is pressed, the tone mode is changed to bass or treble. This receives the signals from the remote control unit. 23. FLUORESCENT DISPLAY For details, see the previous page. 9 RX-5502(A)2007. 5. 179:15AM 10 REMOTE CONTROL OPERATION RANGE Use the remote control unit within a range of about 7 meters (23 feet) and angles of up to 30 degrees aiming at the remote sensor. LOADING BATTERIES 1. Remove the cover. 2. Load two batteries matching the polarity. Remove the batteries when they are not used for a long time. Do not use the rechargeable batteries(Ni-Cd type). 10 RX-5502(A)2007. 5. 179:15AM 11 Operations LISTENING TO A PROGRAM SOURCE Before operation Push the POWER switch. · This unit enters the standby mode and the STANDBY indicator lights up. This means that the receiver is not disconnected from the AC mains and a small amount of current is retained to support the operation readiness. · To switch the power off, push the POWER switch again. Then the power is cut off and the STANDBY indicator turns off. 1. In the standby mode, turn the power on. · Each time the ON/STANDBY button on the front panel, the receiver is turned on to enter the operating mode or off to enter the standby mode. · On the remote control, press the POWER ON button to enter the operating mode or press the STANDBY button to enter the standby mode. 2. Switch the desired speakers on. · You can select the various combinations of speakers depending on where the speakers C or/ and D are installed. · Each time the SPEAKER A/B SELECTOR button is pressed, the speakers are switched on or off as follows : A/B ~ - / - ~ A/ - ~ - /B ~ or (MAIN A/B) or (MAIN -/-) or (MAIN A/-) or (MAIN -/B) ( ) : When the ROOM2 mode is set to on. · Each time the SPEAKER C/D SELECTOR button is pressed, the speakers are switched on or off as follows : ~ C/D ~ - / - ~ C/ - ~ - /D or (R2 C/D) or (R2 -/-) or (R2 C/-) or (R2 -/D) ( ) : When the ROOM2 mode is set to on. · When using the headphones for private listening, switch off all the speakers installed in the main room. Note : · To use ROOM2 function, you should install speakers C or/and D in another room (ROOM2) and set the ROOM2 mode to on. (For details, refer to "CONNECTING SPEAKERS" on page 7 and "ROOM2 PLAYBACK" on page 19. ) 11 RX-5502(A)2007. 5. 179:15AM 12 3. Select the desired input source. Each time the "INPUT SELECT /" buttons are pressed, the input source is changed as follows : TUNER CD AUX DVD TAPE PHONO (Frequency display) 4. [. . . ] 220 mV · Signal to noise ratio, IHF "A" weighted Phono(MM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75 dB Line(CD, DVD, TAPE, AUX) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98 dB · Frequency response Phono(MM), RIAA, 20 Hz~20 kHz . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±0. 3 dB Line(CD, DVD, TAPE, AUX), 10 Hz~100 kHz . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]