User manual SHERWOOD RX-772

[. . . ] Introduction READ THIS BEFORE OPERATING YOUR UNIT ENGLISH This symbol is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING : TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. Caution regarding installation Note : For heat dispersal, do not install this unit in a confined space such as a bookcase or similar enclosure. Do not block ventilation openings or stack other equipment on the top. FOR YOUR SAFETY Units shipped to Australia are designed for operation on 240 V AC only. To ensure safe operation, the three-pin plug supplied must be inserted only into a standard threepin power point which is effectively earthed through the normal household wiring. Extension cords used with the equipment must be three-core and be correctly wired to provide connection to earth. [. . . ] repeatedly REPEAT A/B - to play a specific part (A to B)repeatedly - to skip backward or forward , 8. SPEAKER A, B SELECTOR BUTTONS/INDICATORS These buttons allow you to select various combinations of speakers as follows: To drive A speakers, press only the SPEAKER A button ("A" indicator lights up). To drive B speakers, press only the SPEAKER B button ("B" indicator lights up). To drive both A and B speakers, press the SPEAKER A and B buttons. ("A" and "B" indicators light up). When using headphones for private listening, press these buttons to switch off the speaker A and B ("A" and "B" indicators go off). DIMMER BUTTON Press this button to select the brightness of the fluorescent displays as desired. Each time this button is pressed, the brightness of all fluorescent displays of this unit and Sherwood CD player shch as CD-772, etc. connected by the DIGI LINK changes together as follows: ON dimmer OFF 10. SLEEP BUTTON Press this button to activate the sleep timer for a specified period of time. To resume the previous sound level, press this button again. When adjusting the volume, the mutting effect is turned off. 7. To listen with the headphones. Be sure to switch off both A and B speakers. 12 Listening in the desired tone mode 1. Select the desired tone mode. Each time this button is pressed, the tone mode changes as follows : OFF : To listen to a program source without the tone effect. ON : To listen with the tone effect you adjusted. 2. Adjust the tone (treble and bass) as desired. When adjusting the treble When you select the tone on mode, you can listen to a program source with the tone effect you adjusted. When pressing the TREBLE UP/DOWN(/) or BASS UP/DOWN(/) buttons, the tone level can be adjusted within the range of -10 ~ +10. Notes: Extreme settings at high volume may damage your speakers. In general, the bass and treble levels are adjusted to 0. Adjusting the modes as desired You can adjust the speaker, the tone and the balance modes as desired. 1. Select the desired mode. Each time this button is pressed, the mode is displayed for several seconds and changes as follows : SPEAKER (TONE : ONBASSTREBLE) or BALANCE ( TONE : OFF) 2. Adjust the selected mode as desired. Each time the SELECT konb is rotated, you can adjust the selected mode as follows. Note : The mode display disappears, perform the above step 1 again. 13 Continued When adjusting the SPEAKER mode. A B A + B OFF You can switch on or off the desired speakers. When adjusting the TONE mode. OFF : To listen to a program source without the tone effect. ON : To listen with the tone effect you adjusted. When adjusting the tone (TREBLE and BASS) You can adjust the tone level within the range of -10 ~ +10. Notes : Only when the TONE mode is adjusted to ON, you can adjust the TREBLE and the BASS. Extreme settings at high volume may damage your speakers. In general, the bass and treble levels are adjusted to 0. When adjusting the BALANCE You can adjust the sound volume balance between the left and the right speakers within the range of L10 ~ R 10. [. . . ] 200 mV Signal to noise ratio, IHF "A" weighted Phono (MM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80 dB Line (CD, Tape) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100 dB Frequency response Phono (MM) RIAA, 10 Hz ~ 100 kHz . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±1 dB Line (CD, Tape), 10 Hz~100 kHz . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]