User manual SHERWOOD TX-5505

[. . . ] 5505(G) cover_cover. qxp 2010-07-20 오전 11:23 페이지 1 OPERATING INSTRUCTIONS TX-5505 AM/FM STEREO TUNER TX-5505(G)_ENG_100819_TX-5505(G)_ENG 2010-08-19 오후 5:31 페이지 2 Introduction READ THIS BEFORE OPERATING YOUR UNIT ENGLISH This symbol is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING : TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. FOR YOUR SAFETY Units shipped to Australia are designed for operation on 230 V AC only. To ensure safe operation, the three-pin plug supplied must be inserted only into a standard threepin power point which is effectively earthed through the normal household wiring. Extension cords used with the equipment must be three-core and be correctly wired to provide connection to earth. [. . . ] DIMMER button Each time this button is pressed, the brightness of the fluorescent display changes as follows : → ON → dimmer → OFF 18. MEMORY button Press this button to store the desired stations manually in the memory. 19. TUNING/PRESET MODE button Press this button to select the tunning mode(“P” goes off) or the preset mode (“P” lights up). When listening to FM broadcasts, press this button to enter the RDS menu. 10. TUNING/PRESET knob Rotate this knob to tune in the stations depending on whether the tuning mode or the preset mode is selected. 20. CURSOR ▲/▼/◀/▶and ENTER buttons Press the CURSOR ▲/▼/◀/▶ buttons to select items, etc. then press the ENTER button to confirm your selection. 11. TUNING UP/DOWN (+/-) buttons Press these buttons to tune in the stations without selecting the tuning mode. 21. DISPLAY button Press this button to display RDS information. 7 ENGLISH 13. BAND button TX-5505(G)_ENG_100819_TX-5505(G)_ENG 2010-08-19 오후 5:31 페이지 8 REMOTE CONTROL OPERATION RANGE ENGLISH TUNING / PRESET STANDBY STEREO TUNED RDS ON/ STANDBY DIMMER T/ P MODE BAND AUTO PRESET AM / FM STEREO TUNER TX-5505 • Use the remote control unit within a range of about 7 meters (23 feet) and angles of up to 30 degrees aiming at the remote sensor. LOADING BATTERIES 1. Load two batteries(“AAA” size, 1. 5V) matching the polarity. • Remove the batteries when they are not used for a long time. • Do not use the rechargeable batteries (Ni-Cd type). 8 TX-5505(G)_ENG_100819_TX-5505(G)_ENG 2010-08-19 오후 5:31 페이지 9 Operations LISTENING TO RADIO BROADCASTS • Each time the BAND button on the remote control, the band changes as follows : FM ↔ AM • For details on FM mode, see “Listening to FM stereo broadcasts” on page 12. Before operation • Turn the power on. ON/ STANDBY or ■On the front panel 2. Press the TUNING/PRESET MODE button to select the tuning mode, then rotate the TUNING /PRESET knob over several steps once. • Each time the POWER ON/STANDBY button on the front panel is pressed, the tuner is turned on to enter the operating mode or off to enter the standby mode. • When it is in the standby mode, the STANDBY indicator lights up. This means that the tuner is not disconnected from the AC mains and a small amount of current is retained to support the operation readiness. • On the remote control, press the POWER ON button to enter the operating mode or press the STANDBY button to enter the standby mode. TUNING / PRESET T/ P MODE • Each time the TUNING/PRESET MODE button is pressed, the mode changes as follows : Tuning mode ↔ Preset mode (“P” goes off) (“P” lights up) Auto tuning 1. Select the desired band. BAND ■On the remote control 2. Press the AUTO TUNING button. or Band FM mode • “AUTO” is displayed and the tuner will now search until a station of sufficient strength has been found. The display shows the tuned frequency and the TUNED indicator lights up. • During auto tuning, press the TUNING UP(+)/DOWN(-) buttons to change the received frequency to a higher frequency or a lower frequency. • If the station found is not the desired one, simply repeat this operation. • Weak stations are skipped during auto tuning. FM S T 8 7 . [. . . ] • If the signals are too weak or no RDS service is available, RDS information may not be displayed. 14 TX-5505(G)_ENG_100819_TX-5505(G)_ENG 2010-08-19 오후 5:31 페이지 15 Troubleshooting Guide ENGLISH If a fault occurs, run through the table below before taking your receiver for repair. If the fault persists, attempt to solve it by switching the unit off and on again. If this fails to resolve the situation, consult your dealer. Under no circumstances should you attempt to repair the unit yourself. [. . . ]