User manual SHOWTEC SCENE PILOT 50376

[. . . ] English SCENE PILOT USER'S MANUAL Please read before use Contents Features 1 General Instructions 2 1. Overview 3 1. 1 Front View 3 1. 2 Back View 5 2. Operation Guide 6 2. 1 Record Mode 6 2. 1. 1 Record Enable 6 2. 1. 2 Record Scenes 6 2. 1. 3 Delete a Program 7 2. 1. 4 Delete a Scene 8 2. 1. 5 Add a Scene 9 2. 1. 6 Change a Scene 9 2. 1. 7 Preview a Scene 10 2. 1. 8 Exit Record Mode 11 2. 2 Record AS/AP Scenes 11 2. 3 Run Programs 14 2. 3. 1 Manual Mode 14 2. 3. 2 Audio Mode 15 2. 3. 3 Auto Mode 16 2. 4 Speed Setting 16 2. 5 Send File Dump 17 SCENE PILOT Improvement and changes to specifications, design and this manual, may be made at any time without prior notice. 2. 6 Receive File Dump 18 2. 7 Black-Out Mode 19 2. 8 Initialization 20 Technical Specifications 21 All rights reserved. Features 96 DMX channels 9 chase programs & a AP program 9 strobe programs & a AS program Each chase/strobe program can record a maximum of 48 scenes Either AS or AP program can record a maximum of 60 scenes Each AS or AP scene enables to has its individual speed or fade time Auto/Audio/Manual chase of programs A continuous cycle of Manual or Auto programs Access the scenes from any DMX controller All data can be swapped between two or more units Built-in microphone for Music triggering DMX polarity select Power failure memory 1 General Instructions Read the instruction in this manual carefully and thoroughly, as they give important information regarding safety during use and maintenance. Keep this manual with the unit, in order to consult it in the future. [. . . ] Repeat steps 2-3 in Record Scenes to select the program that holds the scene you wish to delete. 3. Tap the Up/Down button to select the scene you wish to delete. 3 4. Tap the Del button, all LEDs flash briefly indicating this scene is deleted. 8 2. Operation Guide 2. 1. 5 Add a Scene NOTE: You must record scenes before and the program holds less than 48 scenes. 1. Repeat steps 1-3 in Delete a Scene. 2 2. Tap the Up/Down button to select the scene which you wish to add a new scene before. 2 3. Create a scene on your DMX controller, tap the Record button, all LEDs flash briefly indicating you've added a scene(step) into this program. 2. 1. 6 Change a Scene NOTE: The program must record 48 scenes. 2 1. Repeat steps 1-3 in Delete a Scene. 2. Tap the Up/Down button to select the scene you want to change. 9 2. Operation Guide 2. 1. 6 Change a Scene 2 3. Create a scene on your DMX controller, tap the Record button to change the step(scene), all LEDs flash briefly indicating the old scene is replaced by the new one. 2. 1. 7 Preview a Scene NOTE: You must record scenes before you can preview the scenes. 1. Repeat steps 1-3 in Delete a Scene. 2. Tap the Program or Strobe button, the LED near it lights indicating your selection. 2 3. Tap the Up/Down button to select the scene you wish to preview. 4. Tap the Program or Strobe button again to leave this mode. 10 2. Operation Guide 2. 1. 8 Exit Record Mode p300 Tap the Black-out button until the Record LED goes out, this unit is out of Record mode. 2. 2 Record AS/AP Scenes 1. Tap the Up/Down button to select AS or AP . (AS for strobe program, AP for chase program) ap00 3. Operation Guide 2. 2 Record AS/AP Scenes p 4. Create a scene on your DMX controller, tap the Record button, all LEDs flash briefly indicating you've record a scene(step) into this program. 5. Continue recording scenes until you've got a desired program. You may record a maximum of 60 scenes into this AP/AS program. 6. [. . . ] Tap the Up/Down button to adjust the speed within 0. 1-600 seconds, the Segment Display shows the current speed. For Example: 1:00 represents 1 minute, 1. 00 represents 1 second. s202 3. Tap the Program or Strobe button to leave speed setting. 2. 5 Send File Dump 1. Keep pressing the Black-out button for 3 seconds. 2. [. . . ]