User manual SIEMENS GIGASET A510 IP

[. . . ] Gigaset A510 IP / IM-MEA + ZAF en / A31008-M2230-A601-1-UZ43 / title. fm / 8/29/11 Congratulations By purchasing a Gigaset, you have chosen a brand that is fully committed to sustainability. This product’s packaging is eco-friendly!To learn more, visit www. gigaset. com. Gigaset A510 IP / IM-MEA + ZAF en / A31008-M2230-A601-1-UZ43 / title. fm / 8/29/11 Version 5, 23. 09. 2008 Gigaset A510 IP / IM-MEA + ZAF en / A31008-M2230-A601-1-UZ43 / security. fm / 8/29/11 Safety precautions Warning: Be sure to read this user guide and the safety precautions on the CD before using your telephone. Explain their content and the potential hazards associated with using the telephone to your children. > Use only the supplied power adapters, as specified on the back of the base or charger. Use only the cables supplied for fixed line and LAN connection and connect these to the intended port only. > Use only the recommended, rechargeable batteries, as this could otherwise result in significant health risks and personal injury. [. . . ] Default assignment: The VoIP connection is assigned to every registered handset as a receive connection (incoming calls can be received). It is not assigned to any handset as a send connection. The following is shown in the display: a. ¶ Assign connect. No Yes > Press the display key §Yes§ if you wish to change the setting for the send and receive connections of the handset with the internal name INT 1. > Press the display key §No§ if you do not wish to change the setting for this handset. b. INT 1 receiv. calls for Phone Change V OK The receive connections currently assigned to the handset are displayed. You have to press down on the control key w to scroll through the list. > Press the display key §OK§ if you do not wish to change the setting. Continue from e. > Press the display key §Change§ if you wish to change the receive connection setting. c. Receiv. calls for: IP1 f Yes g V If no calls to the VoIP connection IP1 are to be signalled on the handset: > Press right on the control key w to set to No. Back Version 5, 23. 09. 2008 OK 14 Gigaset A510 IP / IM-MEA + ZAF en / A31008-M2230-A601-1-UZ43 / configuration. fm / 8/29/11 Assigning the send/receive connection d. Receiv. calls for: Phone f Yes g V > Press down on the control key w to switch to the next connection. Select either Yes or No as described above. > Repeat the steps for each connection. > Press the display key §OK§ once you have finished configuring the settings for the handset. Back OK The updated list of receive connections is displayed one more time for you to check. Press the display key §OK§ to confirm the assignment. e. INT 1 send calls via: The send connection currently set for the handset is displayed: Phone. Phone Change OK > Press the display key §OK§ if you do not wish to change the setting. Skip the following step. > To change the setting, press the display key §Change§. f. INT 1 send calls via: f IP1 g Which connection/phone number should the handset use to make a call: required connection is displayed (in the example, IP1). > Press right on the control key w repeatedly, until the Back OK > Press the display key §OK§ to save the settings. The connection selected here is used as the standard send connection on this handset if you briefly press the talk key c after entering the number. Version 5, 23. 09. 2008 15 Gigaset A510 IP / IM-MEA + ZAF en / A31008-M2230-A601-1-UZ43 / configuration. fm / 8/29/11 Assigning the send/receive connection Instead of a fixed connection, you can also select Select at each call. Each time you make a call, you must then select the connection you wish to use. You can go on to start the connection assistant for each additional handset registered to the base. The following is displayed in sequence for each handset: Assign connect. (see above) for each registered handset. Completing the installation After successfully configuring the settings, Connec. Afterwards, the handset returns to idle status (an example of the display in idle status): Ð U The following are displayed: Reception between the base and the handset: good to low: Ð ¨ § ¦, no reception: ¥ Charge status of the batteries: = e V U (flat to full) = Battery almost empty (less than 10 minutes talktime) = e V V (charging) INT 1: Internal name of the handset INT 1 12. 09. 10:53 Redial Menu You can configure five additional VoIP connections (VoIP phone numbers) on your Gigaset. In the user guide on the enclosed CD, you will find detailed information about setting up, configuring new connections and operating your phone, as well as possible solutions to frequently asked questions and problems. To ensure that you can always be reached via the Internet, the router must be permanently connected to the Internet. Version 5, 23. 09. 2008 16 Gigaset A510 IP / IM-MEA + ZAF en / A31008-M2230-A601-1-UZ43 / configuration. fm / 8/29/11 Gigaset. net directory entry Entering names in the Gigaset. net directory Gigaset. net* is a VoIP service provided by Gigaset Communications GmbH, which you can use to make free calls to other Gigaset VoIP users across the world. Every Gigaset. net subscriber can create an entry with a name of their choice in the Gigaset. net online directory. Follow the steps below, if you wish to create and entry in the Gigaset. net directory for your phone **: > Press and hold the down arrow on the control key w. > Press down on the control key w repeatedly until Gigaset. net is selected. [. . . ] Adaptors and batteries for cordless phones carry 6 months warranty from the date of purchase. Gigaset Communications authorized Service Centres will replace or repair, if necessary, any defective part/parts free of charge by presenting this certificate of warranty at the Service Centre mentioned overleaf. This Certificate of warranty does not apply if the telephone has: 1. Been misused, mishandled, willfull damaged, neglected, damaged by lightning, improperly repaired, tested, altered improperly in any way. [. . . ]