User manual SIEMENS GIGASET AS140

[. . . ] EN Dear Customer, Gigaset Communications GmbH is the legal successor to Siemens Home and Office Communication Devices GmbH & Co. KG (SHC), which in turn continued the Gigaset business of Siemens AG. Any statements made by Siemens AG or SHC that are found in the user guides should therefore be understood as statements of Gigaset Communications GmbH. Sehr geehrte Kundin, sehr geehrter Kunde, die Gigaset Communications GmbH ist Rechtsnachfolgerin der Siemens Home and Office Communication Devices GmbH & Co. [. . . ] Do not hold the handset against your ear while it is ringing (incoming call). Dispose of the battery pack and telephone in accordance with environmental regulations. Do not pollute the environment. Emergency numbers cannot be dialled if the keypad lock (page 3) is activated!Not all of the functions described in this manual are available in all countries. 2 Setting up the telephone for use Step 1: Connecting the base Opening the battery cover Press down on the battery cover below its upper end and slide the cover down. 1 2 W Connect the phone jack with the phone cord 1 and the mains units (230 V) with the power cord 2 as shown. The two cords must be plugged in at all times. Use only the mains unit supplied (see the bottom of the base). If you ever purchase another phone cord from a store, ensure that the phone conductors are correctly connected: 3-4 connection of the telephone conductors/EURO CTR37. Place the battery leads in the cable guides so that the battery cover cannot catch on the leads and damage them when it is closed. Only insert the recommended rechargeable battery pack, i. e. never use a normal battery pack as this could damage your health and cause injury. Never use non-Siemens battery chargers as this could damage the battery pack. ~ (Enter the number) The number is dialled. (Or you can first press c [dial tone] and then enter the number. ) During the call you can adjust the earpiece volume with t and s. End the call/cancel dialling: Press the end call key a. You can automatically insert a network provider prefix before any number (see Menu Tree, PRESELECT, page 9). Using the directory and other lists Directory and speed dial list These two lists are used in the same way. Directory: Can store up to 20 numbers and associated names. Speed dial list: Can store up to 8 numbers (12 digits max. ), e. g. private phone numbers, prefixes of network providers ("Call-by-Call") etc. Press the h or C key to open the required list then press MENU. The following functions are available: EDIT ENTRY NEW ENTRY SHOW ENTRY DELETE ¢c. Answering a call Your handset rings and you wish to take the call: Press the talk key c. If "Auto Answer" is active (page 6) just lift the handset out of its base/charging cradle. Add/edit number and use to dial Save new phone number Show/edit number Delete a single entry Clear the list: h/C¢MENU¢L ¢OK. Calling Line Identification When you get a call, the caller's number will be displayed on your handset; the caller's name will be displayed if it is stored in the directory . Requirements: 1 You have asked your network provider for the caller's number (CLIP) to be displayed on your handset screen. 2 The caller has asked the network provider for his number to be identified (CLI). The display shows if you have not requested CLIP, WITHHELD if the caller has withheld CLI, or UNAVAILABLE if it has not been requested. Storing a number in the directory/speed dial list h/C¢ MENU ¢ NEW ENTRY ~OK ~OK Enter phone number and confirm. [. . . ] Cords not routed Check cord routing (page 2). correctly 8 Service (Customer Care) You can get assistance easily when you have technical questions or questions about how to use your device by using our online support service on the Internet at: http://www. siemens. com/gigasetcustomercare This site can be accessed at any time wherever you are. It will give you 24/7 support for all our products. It also provides a list of FAQs and answers plus user guides for you to download. [. . . ]