User manual SIEMENS GIGASET AS28H

[. . . ] This can cause static. $ Only use the mains adapter supplied. Contact with liquid ! Fit only the recommended, rechargeable batteries (¢ page 9), i. e. never use any other battery type or non-rechargeable batteries as this could result in significant health risks and personal injury. The operation of medical appliances may be affected. Be aware of the technical conditions in your particular environment, e. g. [. . . ] The actual registration procedure will depend on the type of base station. Automatically register the AS28H handset to the Gigaset AS280DUO/AS285 base station Put into base V ¤ Place the handset with the display facing up in the base station. MENU Registering V The handset registers automatically. Do not remove the handset from the base station during this time. Manually register the AS28H handset You must activate manual registration of the handset on both the handset and the base station. On the handset: MENU Settings OK Handset OK Register HS ¢ ¢¢ ¢¢ ¢ Enter the base station system PIN (default setting: 0000) ¢ OK. Registering V The registration screen is displayed. 2. On the base station: Within 60 seconds of entering the system PIN, press and hold the registration/paging key (min. See also the user guide for the base station. After successful automatic or manual registration, the idle screen is displayed: V INT MENU Charge status of the batteries: ­ = e V U (flat to full) ­ = flashes: batteries almost flat ­ e V U flashes: charging The handset is assigned the lowest unassigned internal number (1­4). If more than one handset is registered to the base station, the internal handset number appears in the top left of the display, e. g. If the internal numbers 1­4 are already assigned to other devices, number 4 will be overwritten. Please note Only place the handset in the base station or charging cradle that is intended for it. 6 Initial charging and discharging of the batteries The correct charge level can only be displayed if the batteries are first fully charged and discharged. 8h ¤ Place the handset in the base station or charging cradle for eight hours. ¤ Then remove the handset from the base station or charging cradle and do not replace it until the batteries are fully discharged. Please note After the first battery charge and discharge you may replace your handset in the base station or charging cradle after every call. reasons. Always repeat the charging and discharging procedure if you remove the batteries The batteries may warm up during charging. After a while, the charge capacity of the batteries will decrease for technical Setting the date and time Set the date and time so that the correct date and time can be assigned to incoming calls, and so that the alarm can be used. MENU Settings OK Date/Time OK Date: ~ (enter the day, month and year in 6-digit format) OK Time: ~ (enter hours and minutes in 4-digit format) OK (display message: Saved) a (press and hold to return to idle status) ¢ ¢ ¢ ¢ ¢ ¢ ¢¢ ¢ ¢ ¢ Please note When entering the time and date, you can move the position of an entry to the left or right by pressing the control button up or down. Display in idle status Once the phone is registered and the time set, the idle display is shown as in this example. INT 11:56 MENU V If you place a deactivated handset in the base station or charging cradle, it will automatically activate. If you have any questions about using your phone, please read the tips on troubleshooting page 9) or contact our Customer Care team page 9. ("Questions and answers" Activating/deactivating the handset Press and hold the end call key a to activate or deactivate the handset. ¢ ¢ 7 Making calls Making external calls and ending calls External calls are calls using the public telephone network. ~ (Enter the phone number) The phone number is dialled. (Or you can first press and hold c [dial tone] and then enter the number. ) During the call you can adjust the earpiece volume using t and set the volume with u. End the call/cancel dialling: Press the end call key a. Using the directory and lists Directory To open the directory: press h. You can save up to 80 phone numbers (max. 32 digits) with corresponding names (max. Enter letters/characters page 9. ¢c. ¢ Accepting a call The handset indicates an incoming call by ringing and by a display on the screen. Press the talk key c to accept the call. When Auto Answer is activated (see Menu tree, page 10), simply remove the handset from the base station/charging cradle. [. . . ] For fast and dependable assistance with any repairs or guarantee/warranty claims, contact our Service Centre. 1 700 700 727 Please have your proof of purchase ready when calling. Replacement or repair services are not offered in countries where our product is not sold by authorised dealers. Specifications Recommended batteries Technology: Nickel-metal-hydride (NiMH) Size: AAA (Micro, HR03) Voltage: 1. 2 V Capacity: 400­800 mAh We recommend the following types of battery: GP 550/700 mAh Yuasa Phone 700/800 mAh Peacebay 550/650 mAh (Valid at the time of going to press) The handset is supplied with recommended batteries. General specifications DECT standard GAP standard Range Environmental conditions in operation is supported is supported up to 300 m outdoors up to 50 m indoors +5°C to +45°C, 20% to 75% relative humidity Authorisation This device is intended for connection to analogue networks outside the EEA (with the exception of Switzerland) depending on national type approval. Country-specific requirements have been taken into consideration. [. . . ]