User manual SIEMENS GIGASET C47H

[. . . ] s Issued by Gigaset Communications GmbH Schlavenhorst 66, D-46395 Bocholt Gigaset Communications GmbH is a trademark licensee of Siemens AG Gigaset Communications GmbH 2008 All rights reserved. www. gigaset. com Gigaset C47H Gigaset The handset at a glance The handset at a glance 16 INT 1 15. 11. 07 INT V 1 2 09:45 SMS 3 4 5 15 14 13 12 11 10 9 8 6 7 Please note: Illustration of handset on a base station with SMS functionality. 1 Display (screen) in idle status 2 Charge status of the batteries = e V U (flat to full) = flashes: batteries are almost flat e V U flashes: battery charging 3 Display keys (page 9) 4 Message key Access to calls and message lists; Flashes: new message or new call 5 End call key, On/Off key End call, cancel function, go back one menu level (press briefly), back to idle status (press and hold), activate/deactivate handset (press and hold in idle status) 6 Hash key Keypad lock on/off (press and hold in idle status); Toggle between upper/lower case and digits (press and hold) 7 Call-by-call list key Open call-by-call list 8 Microphone 9 Recall key - Confer (flash) - Insert a dialling pause (press and hold) 10 Star key Ringer tones on/off (press and hold); With an open connection: switch between dial pulsing/touch tone dialling (press briefly); Open special characters table 11 Connection socket for headset 12 Key 1 Dial network mailbox (press and hold) 13 Talk key Accept a call, open last number redial list (press briefly), start dialling (press and hold); When writing an SMS: send SMS 14 Handsfree key Switch between earpiece and handsfree mode; Lights up: handsfree activated Flashes: incoming call 15 Control key (page 8) 16 Signal strength i (high to low) | flashes: no reception 1 Contents Contents The handset at a glance . 3 Gigaset C47H More than just a telephone . Changing the handsfree/ earpiece volume . [. . . ] The connection to which the room monitor is diverted must not be blocked by an activated answer machine. v Room Monitor s Scroll to the Call to: line. Enter number as described in "Activating the room monitor and entering the destination number" (page 15). Save the changes. Editing a set external destination number v Room Monitor s Scroll to the Call to: line. Enter number as described in "Activating the room monitor and entering the destination number" (page 15). 15 Editing a set internal destination number Setting the handset Deactivating the room monitor remotely Preconditions: The phone must support touch tone dialling and the room monitor should be set for an external destination number. Accept the call from the room monitor and press keys 9 ;. The room monitor function will deactivate after the call ends. There will be no further room monitor calls. no ringer tone) on the handset will remain activated until you press the display key OFF on the handset. To reactivate the room function with the same phone number: Turn on the activation again and save with Save. SMS Service Assign key with the menu for ordering info services (depending on base station). Assign key with the menu for activating SMS notification (depending on base station). Withhold phone number identification for next call. If a function or number has already been assigned to the left display key, the selected function (or its abbreviation) will be displayed in the lowest display line above the display key. Starting a function With the handset in idle status, press the display key briefly. The function menu is opened. Setting the handset Your handset is preconfigured, but you can change the settings to suit your individual requirements. Changing the display language You can view the display texts in different languages. v Handset Language The current language is indicated by . s Select a language and press OK. Quick access to functions The display keys have preset functions. To start the function, you then simply need to press the button. a Press and hold (idle status). Changing a display key assignment key. The list of possible key assignments is opened. The following can be selected: INT Internal calls (see page 12). SMS Assign key with the menu for SMS functions (depending on base station). Press and hold the left or right display If you accidentally choose a language you do not understand: v 5 4 Press keys in sequence. s Select the correct language and press OK. 16 Setting the handset Setting the display You have a choice of four colour schemes and several different contrasts. v Display Colour Scheme Select and press OK. [. . . ] Select contrast and press the display key Save. r Press the s key. Press on the right or left of the control Press the display key Save to confirm the selection. key to set the contrast. The fourth line is marked with [ ] to show it is active. Enter the date using the digit keys. 25 Accessories Save the changes. Then press and hold the a key. The handset switches to idle status. you release the key, the highlighted character is inserted into the input field. Setting upper/lower case or digits Press the hash key # briefly to switch from "Abc" mode to "123" and from "123" to "abc" and from "abc" to "Abc" (upper case: 1st letter upper case, all others lower case). [. . . ]