User manual SIEMENS GIGASET S680

[. . . ] s Issued by Gigaset Communications GmbH Schlavenhorst 66, D-46395 Bocholt Gigaset Communications GmbH is a trademark licensee of Siemens AG Gigaset Communications GmbH 2008 All rights reserved. www. gigaset. com Gigaset S680 Gigaset Handset at a glance Handset at a glance 18 17 16 V 1 2 INT 1 15. 11. 07 ?09:45 SMS 3 4 5 15 14 13 12 11 10 9 8 6 7 The base station at a glance 1 Display (screen) in idle status 2 Charge status of the batteries = e V U (flat to full) = flashes: batteries almost flat e V U flashes: batteries charging 3 Display keys (page 10) 4 Message key Access to calls and message lists; Flashes: new message or new call 5 End call key, On/Off key End call, cancel function, go back one menu level (press briefly), back to idle status (press and hold), activate/deactivate handset (press and hold in idle status) 6 Hash key Keypad lock on/off (press and hold in idle status), Toggle between upper/lower case and digits (press and hold) 7 Call-by-call list key Open call-by-call list 8 Microphone 9 Recall key - Confer (flash) - Insert a dialling pause (press and hold) 10 Star key Ringer tones on/off (press and hold); With an open connection: switch between dial pulsing/touch tone dialling (press briefly) Open special characters table 11 Key 1 Dial network mailbox (press and hold) 12 Connection socket for headset 13 Talk key Answer a call, open last number redial list (press briefly), start dialling (press and hold) When writing an SMS: send SMS 14 Handsfree key Switch between earpiece and handsfree mode; Lights up: handsfree activated; Flashes: incoming call 15 Control key (page 10) 16 Bluetooth activated (page 47) 17 Eco mode activated (page 12) 18 Signal strength i (high to low) | flashes: no reception Registration/paging key (page 35) 1 Contents Contents Handset at a glance . 4 Gigaset S680 More than just a telephone . [. . . ] You are connected straight to the network mailbox. You will hear the network mailbox announcement. Configuring fast access for the network mailbox With fast access, you can dial the network mailbox directly. Fast access is set for the network mailbox. You only need to enter the number of the network mailbox. Viewing the network mailbox report When a message is recorded, you receive a call from the network mailbox. If you have requested Calling Line Identification, the network mailbox number will be displayed. If you take the call, the new messages are played back. If you do not take the call, the network mailbox number will be saved in the missed calls list and the message key flashes (page 23). v Voice Mail Set Key 1 Network Mailb. ~ Enter the number for the network mailbox. The setting for fast access applies to all Gigaset S68H handsets. Configuring fast access for the network mailbox and entering the network mailbox number 34 Using several handsets Using several handsets Registering handsets You can register up to six handsets to your base station. A Gigaset S68H handset can be registered to up to four base stations. Manual registration of Gigaset S68H to Gigaset S680 You must activate manual registration of the handset on both the handset and the base station. Once it has been registered, the handset returns to idle status. The handset's internal number is shown in the display e. g. If not, repeat the procedure. Automatic registration of Gigaset S68H to Gigaset S680 Precondition: The handset must not already be registered to a base station. Registering the handset to the base station occurs automatically. Place the handset in the base station with its display facing forward. During this process, the registration procedure appears in the display and the name of the base station flashes, e. g. When the handset has registered successfully, its screen displays its internal number, e. g. The handset is assigned the lowest available internal number (16). If all internal numbers 16 have been assigned, number 6 is overwritten, provided the handset with the internal number 6 is in idle status. On the handset v Handset Register H/Set s Select base station, e. g. ~ Enter the system PIN of the base station (the default is 0000) and press OK. You will see flashing on the display e. g. Base 1. On the base station Within 60 sec. [. . . ] 39 Activating/deactivating network mailbox. 45, 46 Appointment/anniversary display missed . 46 Appointments activating/deactivating . 45 Area code setting own dialling code . [. . . ]