User manual SIEMENS GIGASET S880

[. . . ] s Issued by Gigaset Communications GmbH Schlavenhorst 66, D-46395 Bocholt Gigaset Communications GmbH is a trademark licensee of Siemens AG Gigaset Communications GmbH 2008 All rights reserved. www. gigaset. com Gigaset S880 - S885 Gigaset The handset at a glance The handset at a glance 17 16 INT 1 V 1 2 08. 03. 17 INT 09:45 3 4 5 15 14 13 12 11 10 9 8 6 7 1 Display (screen) in idle status 2 Charge status of the batteries = e V U (flat to full) = flashes: batteries almost flat e V U flashes: batteries charging 3 Display keys (page 11) 4 Message key Access to calls and message lists; Flashes: new message or new call 5 End call key, On/Off key End call, cancel function, go back one menu level (press briefly), back to idle status (press and hold), activate/deactivate handset (press and hold in idle status) 6 Hash key Keypad lock on/off (press and hold in idle status); Toggle between upper/lower case and digits (press and hold) 7 IP key 8 Microphone 9 Recall key - Confer (flash) - Insert a dialling pause (press and hold) 10 Star key Ringer tones on/off (press and hold); With an open connection: switch between dial pulsing/touch tone dialling (press briefly); Open special characters table 11 Connection socket for headset 12 Key 1 Dial answering machine (S885 only) 13 Talk key Answer a call, open last number redial list (press briefly), start dialling (press and hold); 14 Handsfree key Switch between earpiece and handsfree mode; Lights up: handsfree activated Flashes: incoming call 15 Control key (page 11) 16 Answering machine icon (S885 only) Answering machine switched on Flashes: answering machine is recording a message or is being operated by another internal party 17 Signal strength i (high to low) | flashes: no reception 1 The base station at a glance The base station at a glance You can use the keys on the base station to register handsets to the base station, search for handsets ("paging", see page 25) and operate the integrated answering machine (Gigaset S885 only). During message playback: 3 Play/stop key: Play back new messages from the answering machine or cancel the playback (press briefly). Play back new and old messages (press and hold). 4 Skip to next message (press once) or next message but one (press twice). [. . . ] If necessary, place the handset in the charging cradle. This ensures that the batteries do not run down. Ideally the handset should be positioned 1 to 2 metres away from the baby. The microphone must be directed towards the baby. The connection to which the room monitor is diverted must not be blocked by an activated answering machine. 27 Setting the handset Activating the room monitor and entering the number to be called v Room Monitor Change multiple line input: Room M. : Select On to activate. Call to: Press the display key Edit and enter destination number. External number: Select number from the directory or enter directly. Internal number: INT s (Select handset or Call All if all registered handsets are to be called) OK. Level: Set noise level sensitivity (Low or High). Save the changes. Deactivating the room monitor remotely Preconditions: The phone must support touch tone dialling and the room monitor should be set for an external destination number. Accept the call from the room monitor and press keys 9 ;. The room monitor function will deactivate after the call ends. There will be no further room monitor calls. no ringer tone) on the handset will remain activated until you press the display key OFF on the handset. To reactivate the room function with the same phone number: Turn on the activation again and save with Save (page 28). Setting the handset Your handset is preconfigured, but you can change the settings to suit your individual requirements. Changing a set external destination number v Room Monitor s Scroll to the Call to: line. Enter number as described in "Activating the room monitor and entering the number to be called" (page 28). Save changes (page 44). Changing the display language You can view the display texts in different languages. v Handset Language The current language is indicated by . s Select a language and press OK. Changing a set internal destination number v Room Monitor s Scroll to the Call to: line. Enter number as described in "Activating the room monitor and entering the number to be called" (page 28). Save the changes. a Press and hold (idle status). If you accidentally choose a language you do not understand: v54 Press keys in sequence. [. . . ] 2. 5 mm 47 Index Index A Access protection . 35 Announcement mode (answering machine). 36 recording a personal announcement/ announce only . 21, 22 Answering machine, see also Network mailbox Approval . [. . . ]