User manual SIEMENS PHONE ADAPTER

[. . . ] All rights including rights created by patent grant or registration of a utility model or design are reserved. MICROMASTER® is a registered trademark of Siemens Other functions not described in this document may be available. However, this fact shall not constitute an obligation to supply such functions with a new control, or when servicing. We have checked that the contents of this document correspond to the hardware and software described. [. . . ] See Figure 3-7 for details on how to read motor data. Changing motor parameters is not possible unless P0010 = 1. You must set P0010 back to 0 in order to initiate a run. PHONE ADAPTER Operating instructions 6SE6400-5CA00-0BP0 43 3 Commissioning International English PHONE ADAPTER 44 Operating instructions 6SE6400-5CA00-0BP0 International English 4 Using the PHONE ADAPTER 4 Using the PHONE ADAPTER An explanation of the various methods of controlling the inverter An outline of some of the more commonly used parameters of the PHONE ADAPTER which will allow the user to configure the inverter for a number of applications. A brief summary of all the inverter's control modes and an introduction to the inverter's fault and warning reporting capability. More detailed information can be found in the Parameter List and the Reference manual associated with the PHONE ADAPTER. This Chapter contains: 4. 1 4. 2 4. 3 4. 4 4. 5 Frequency Setpoint (P1000) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 Command Sources (P0700). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 OFF and braking Functions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 Control Modes (P1300) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 Faults and warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 PHONE ADAPTER Operating instructions 6SE6400-5CA00-0BP0 45 4 Using the PHONE ADAPTER International English Warnings When operating electrical devices, it is impossible to avoid applying hazardous voltages to certain parts of the equipment. Emergency Stop facilities according to EN 60204 IEC 204 (VDE 0113) must remain operative in all operating modes of the control equipment. Enable DC braking: see P0701 to P0708 Set DC braking period: see P1233 Set DC braking current: see P1232 Set DC braking start frequency: see P1234 Note If no digital input is set to DC braking and P1233 0, DC braking will be active after every OFF1 command with the time set in P1233. 4. 3. 5 Compound Braking Compound Braking is possible with both OFF1 and OFF3. For Compound Braking a DC component is added to the AC current. Set the braking current: see P1236 4. 3. 6 Braking with external braking resistor Braking with an external resistor is a method of braking that allows a smoothed, controlled reduction in motor speed in a linear manner. The technique is also known as Dynamic braking. For further details please refer to the Applications Handbook. PHONE ADAPTER 48 Operating instructions 6SE6400-5CA00-0BP0 International English 4 Using the PHONE ADAPTER 4. 4 Control Modes (P1300) The various modes of operation of the PHONE ADAPTER control the relationship between the speed of the motor and the voltage supplied by the inverter. A summary of the control modes available are listed below: Linear V/f control, P1300 = 0 Can be used for variable and constant torque applications, such as conveyors and positive displacement pumps. Linear V/f control with FCC (Flux Current Control), P1300 = 1 This control mode can be used to improve the efficiency and dynamic response of the motor. Parabolic V/f control P1300 = 2 This mode can be used for variable torque loads, such as fans and pumps. Multi-point V/f control P1300 = 3 For information regarding this mode of operation, please consult the MM440 Reference Manual. Linear V/f control with ECO mode P1300 = 4 This feature automatically increases and decreases the motor voltage in order to search for the minimum power consumption. It is designed to function when the preset setpoint speed is reached. [. . . ] There are three routes for the manufacturer/assembler to demonstrate compliance: 9. 1. 1 Self-Certification This is a manufacturer's declaration that the European standards applicable to the electrical environment for which the apparatus is intended have been met. Only standards that have been officially published in the Official Journal of the European Community can be cited in the manufacturer's declaration. 9. 1. 2 Technical Construction File A technical construction file can be prepared for the apparatus describing its EMC characteristics. This file must be approved by a `Competent Body' appointed by the appropriate European government organization. This approach allows the use of standards that are still in preparation. 9. 1. 3 EC Type Examination Certificate This approach is only applicable to radio communication transmitting apparatus. [. . . ]