User manual SIEMENS S4943N1

[. . . ] en Summary of instructions for dishwasher Brief and handy: everything your dishwasher needs. Before using for the first time, read the installation and operating instructions! Setting the water softening system * Find out the water hardness at your water utility company and enter below Read off the setting °dH 0­6 7­16 °fH 0­11 12­29 °Clarke mmol/l 0­8 9­20 0­1, 1 1, 2­2, 9 3, 0­3, 7 3, 8­6, 2 Setting 0 1 2 3 Quickly sorted and then select a setting ­ Hold down programme button B and switch on the main switch, then release the buttons. display flashes and buttons A and B illuminate (water hardness setting was set to 2 at the factory). [. . . ] PLOP! Turn on the tap Water ready Switch on the appliance Close the door. Press the On/Off switch, the last selected programme starts automatically. Quick, economical or intensive . . . Overview of programmes This overview indicates the max. The programmes which correspond to your appliance can be found on your appliance fascia. Duration in minutes Intensive 70_ Normal 65_ Eco 50_ Gentle 40_ Quick 35_ Prerinse 450 H 5600 053 022 ( 8411-1) Select programme The programme data are values measured in the laboratory in compliance with Standard EN 50242. Deviations is practice are possible. 103 1, 40 Water consumption in litres 20 Power consumption in kWh 140 1, 35 18 155 0, 80 13 71 0, 70 14 30 0, 50 10 20 0, 10 4 Off we go Programme progress / Rinsing noises Example: Eco programme Cleaning / Final rinse Dry Switch off the appliance Everything o. k. When the "programme end" display illuminates, switch off the main switch. Alternating rinsing and pumping noises Start No rinsing noises 15­35 min m End display After the drying cycle, water is pumped out for approx. The programme has not ended until the end display m lights up Maintenance and care Strainers . . . Check, if required, clean Rotate filter cylinder, remove filter system . . . For perfect rinsing results . . . rinse under flowing water . . . Screw in filter system NOTE MARK! Cleaning the waste-water pump * * With some models ­ Ladle out water and remove filters ­ Unscrew cover (Torx T20) ­ Check area of fan impeller for foreign objects ­ Screw in cover and insert filters Spray arms . . . Remove blockages/deposits Pull lower arm upwards . . . Unscrew upper arm . . . Clean spray nozzles under flowing water (perhaps with toothpick) . . . Insert lower arm . . . Screw in upper arm Eliminating minor faults yourself . . . Fault Possible Cause . . . Self-help pays! Remedy Fault Dishes not clean Possible Cause Utensils are situated too close to each other or on top of each other Too little cleaning product Unsuitable programme selected Spray nozzles blocked Filters dirty, not installed securely Spray arms blocked Remedy Spread out the utensils, avoid contact between the utensils. Follow manufacturer's specifications (detergent). Arrange the utensils so that the spray arms can rotate freely. Residual water in the device Waste-water pump blocked Programme not yet ended Clean waste-water pump (see above). Close and switch on the appliance and wait until the programme ends (end of programme display lights up) or terminate programme (see Terminating the programme). Sand or grainy residues on dishes Device does not work/stops Supply fitting not open Supply hose kinked Supply fitting jammed or calcified Open supply fitting. If the flow rate is less, replace the supply fitting. [. . . ] ­ To continue the programme, switch on the main switch again. Cancelling the programme While the programme is running, simultaneously press the two Reset buttons for approx. 1 minute after the programme has ended, the "programme end" display illuminates. Arranging utensils correctly Switch off the appliance. Arrange dishwasher-proof utensils (without any residual ash, wax, grease, ink, sticky labels; remove large remnants of jam, dairy products and food) according to the operating instructions and check that the spray arms can rotate freely. [. . . ]