User manual SIEMENS SANTIS-AB

[. . . ] If the SANTIS-ab is damaged, inform immediately your network provider. 4 2. Operating Modes The connection to the public telephone network as well as the selection of one of the following three operating modes must be done by an authorized person, e. g. Pairgain S- and a/b-interfaces available Only S-interface available Only a/b-interfaces available 5 3. [. . . ] and Pairgain: The MSNs can only be set by authorized persons. 13 Hot Line Command-No / Meaning 181 hot line number for a/b1-interface 182 hot line number for a/b2-interface 191 hot line switch for a/b1-interface 192 hot line switch for a/b2-interface Parameter value 0-16 digits 0-16 digits 0 = hot line off 1 = hot line on 0 = hot line off 1 = hot line on Default ----0 0 Hot line means that a predefined number is dialed automatically after hook off (e. g. In order to switch the hot line off, hook off and start immediately to dial the offcommand. and Pairgain: a/b1 via a/b1 only; a/b2 via a/b2 only. 14 Emergency Mode Priority Switch Command-No / Meaning Parameter value 210 emergency mode 0 = S-interface priority 1 = a/b-interface *) *) First hooked off, first served Default 0 Emergency mode means failure of the mains. Then only one terminal equipment can be operated at either the S- or one of both the a/b-interfaces. The preferred interface can be selected by this command. If set to `1', the emergency priority of all the S-bus terminal equipments must be disabled. Restrictions: The switch is only available in the NT+2ab mode. NT+2ab/CA restr. : Can only be set by authorized persons. Pairgain: Automatically set to `1' and can not be changed. 15 Type of Terminal Selection (HLC) Command-No / Meaning Parameter value 221 type of terminal 0 = audio equipment at 1 = telephony a/b1-interface 2 = fax gr. 2/3 (HLC) 3 = modem(audio) 222 type of terminal 0 = audio equipment at 1 = telephony a/b2-interface 2 = fax gr. 2/3 (HLC) 3 = modem(audio) Default 0 0 In order to have all the benefits of an ISDN the SANTIS-ab should know the type of terminal equipment connected to both the a/b-interfaces. and Pairgain: a/b1 via a/b1 only; a/b2 via a/b2 only. 16 Clear Back Time Delay Switch Command-No / Meaning Parameter value 311 clear back time 0 = immediate delay 1 = 3 minutes at a/b1-interface 312 clear back time 0 = immediate delay 1 = 3 minutes at a/b2-interface Default 1 1 If you answer a phone call, you can hook on and the connection is still available, if you hook off again within 3 minutes (the caller must not hook on). This feature is called `clear back time delay' and can be suppressed by this command. and Pairgain: a/b1 via a/b1 only; a/b2 via a/b2 only. 17 PABX-Switch Command-No / Meaning 320 address selection Parameter value 0 = standard 1 = PABX Default 0 If both the a/b-interfaces are connected to a PABX, this parameter should be set to `1'. Restrictions: NT+2ab/CA restr. : Can only be set by authorized persons. [. . . ] 24 Remarks: · There is a time limitation for the programming. If one sequence is not finished within 30 seconds, an internal generated busy tone will be switched on. · Check if the programming was successful with test calls between two a/b-interfaces or from an ISDN-telephone set to an analog one and vice versa. 25 6. Check the green LEDs on the top of the case: both must light steadily. [. . . ]