User manual SIEMENS TC 40400

[. . . ] To the maximum extent permitted by applicable law, Siemens further disclaims all warranties, including without limitation any implied warranties of merchantability, fitness for a particular purpose and noninfringement of third-party rights. The entire risk arising out of the use or performance of the Product and documentation remains with Recipient. This Product is not intended for use in life support appliances, devices or systems where a malfunction of the product can reasonably be expected to result in personal injury. Applications incorporating the described product must be designed to be in accordance with the technical specifications provided in these guidelines. [. . . ] ("PS" lock is also referred to as phone or antitheft lock). ME is waiting for Master Phone Code, if the above "PS" lock password was incorrectly entered three times. PH-SIM PUK Factory set SIM locks PH-FSIM PIN ME is waiting for phone-to-very-first-SIM card. Necessary when "PF" lock was set. When powered up the first time, ME locks itself to the first SIM card put into the card holder. As a result, operation of the mobile is restricted to this one SIM card (unless the PH-FSIM PUK is used as described below). 10. 01. 2003 TC35i_ATC_V00. 01 Page 117 of 257 TC35i AT Command Set PRELIMINARY PH-FSIM PUK ME is waiting for phone-to-very-first-SIM card unblocking password to be given. Necessary when "PF" lock is active and other than first SIM card is inserted. ME is waiting for network personalisation password ME is waiting for network personalisation unblocking password ME is waiting for network subset personalisation password ME is waiting for network subset unblocking password ME is waiting for service provider personalisation password ME is waiting for service provider personalisation unblocking password ME is waiting for corporate personalisation password ME is waiting for corprorate personalisation unblocking password PH-NET PIN PH-NET PUK PH-NS PIN PH-NS PUK PH-SP PIN PH-SP PUK PH-C PIN PH-C PUK See Chapters 4. 21 and 7. 15 for information on lock types. Write command Response AT+CPIN=<pin> [, <new pin>] The write command lets the ME store the entered password. This may be for example the SIM PIN1 to register to the GSM network, or the SIM PUK1 to replace a disabled PIN with a new one, or the PH-SIM PIN if the client has taken precautions for preventing damage in the event of loss or theft etc. OK If error is related to ME functionality: +CME ERROR: <err> If no PIN request is pending (for example if PIN authentication has been done and the same PIN is entered again) ME responds +CME ERROR: operation not allowed. No action is required from your part. Parameter <pin> <new pin> password (string type), for example SIM PIN or, if requested, one of the unblocking keys, such as SIM-PUK or PH-SIM PUK. If the ME is waiting for an unblocking key, use <pin> to enter the unblocking key, followed by <newpin> to specify the password. The handling of PIN2 varies with the provider. PIN2 may either be a specific code supplied along with an associated PUK2, or a default code such as 0000. In either case, the client is advised to replace it with an individual code. Incorrect input of PUK2 will permanently block the additional features subject to PIN2 authentification, but usually has no effect on PIN1. PIN2 consists of 4 digits, PUK2 is an 8-digit code only. To unblock a disabled PIN2 you have three options: § You can enter AT+CPIN2=PUK2, new PIN2. § You can enter AT+CPWD="P2", PUK2, new PIN2. § You can use the ATD command followed by the GSM code **052*PUK*newPIN*newPIN#;. If the mobile was locked to a specific SIM card (= "PS" lock or phone lock), the PUK that came with the SIM card cannot be used to remove the lock. After three failed attempts to enter the correct password, ME returns +CPIN: PH-SIM PUK (= response to read command AT+CPIN?), i. e. it is now waiting for the Master Phone Code. [. . . ] enter PIN2) Unlock "PS" lock with Master Phone Code Registration of net password (change call barring password) Call barring (see also Chapter 8. 4. 1) (choice of *, #, *#)33*Pw*BS# (choice of *, #, *#)331*Pw*BS# (choice of *, #, *#)332*Pw*BS# (choice of *, #, *#)35*Pw*BS# (choice of *, #, *#)351*Pw*BS# #330*Pw*BS# #333*Pw*BS# #353*Pw*BS# Act/deact/int BAOC Act/deact/int BAOIC Act/deact/int BAOIC exc. home Act/deact/int. All Inc. Barring Services ^SCLCK: <fac>, <status>, <class> [, . . . ] Refer to Chapter 4. 21 for a description of parameters and Chapter 8. 4. 1 for differences regarding the responses ^SCLCK and +CLCK. TC35i_ATC_V00. 01 Page 252 of 257 10. 01. 2003 TC35i AT Command Set PRELIMINARY *# code Call Hold / Multiparty C[C] in call USSD messages [C]. . . [C]# (varies with the serving network) C[C] (excluded 1[C]) (varies with the serving network) Send USSD message Send USSD message +CME ERROR: <err> / OK OK (see Chapter 4. 48, p. 138) +CME ERROR: <err> / Call hold and multiparty +CME ERROR: <err> / OK (see Chapter 4. 16, p. 85) Functionality Possible response(s) Abbreviations of codes and responses used in Table 14 Codes / parameters to be sent with ATD ZZ = type of supplementary services: Barring services 330 All services Not specified DN = dialing number: String of digits 0-9 BS = basic service Voice 11 equivalent to parameter <class> FAX 13 SMS 16 SMS +FAX 12 Voice + FAX 19 Voice + SMS + FAX 10 Data circuit asynchron 25 Data circuit synchron 24 PAD 27 Packet 26 Data circuit asynchron + PAD 21 Data circuit synchron + packet 22 Data circuit asynchron + syncron. [. . . ]