User manual SIM2 HT300 XTRA

[. . . ] User and Installation Manual The home theater projector HT300 XTRA cod. 46. 0328. 000 BACK LIGHT Turn on the back light LIGHT STAND-BY Switches off to stand-by. 0-9 Keys Switch on from stand-by and allow direct source selection. ESCAPE Deactivates the On Screen Display. SOURCE Displays the Source Selection menu. Not active in this model. Up/Down/Left/Right Arrow keys Navigate through and make adjustments to the On Screen menus. MENU + Activates the On Screen Display menus. [. . . ] 22 Connect/disconnect the special Remote Input Interface cable only when the projector is switched off and disconnected from the mains (switch in position O). 12 XTRA The output can be used to control a screen masking system; its output can be set with the "Screen control" adjustment in the "Aspect" menu. This output allows reduction in the area of a 16:9 screen, into a 4:3 format, by activating a screen masking system (refer to screen manufacturer for further information). C SYN DVI RS232 INTERFACE CONNECTOR It is possible to control the projector through a personal computer. First, load the appropriate projector control software onto your PC, then simply connect this input to a cable from your PC's RS232 serial port (Fig. 25 7 KEYBOARD PAD Eight push buttons, at the rear of the projector, will allow complete operation without the use of the remote control. Menu Switches off to stand-by. Navigates Menu pages. Auto Selects Auto Adjust (automatic optimisation of the displayed image). Up/Down/Left/Right arrow keys Navigate through and make adjustments to the On Screen menus. Arrow Up/Down switch on from stand-by and recall Source Selection menu. -Focus-Esc De-activates the On Screen Display and gives access to the lens Zoom/Focus adjustment functions. 13 XTRA 8 REMOTE CONTROL Insert the batteries, taking care to match the polarity, as indicated in the battery recess of the remote (Fig. The remote control sends commands to the projector via infrared signals. It is possible to control the projector by pointing the remote control at the screen; the sensor at the front of the projector will pick up the reflected infrared commands. 27). + + + + - four 1. 5V AAA alkaline batteries DVI C-SYNC LIGHT Fig. 26 ZOOM F1 Change the batteries in the remote control if experiencing difficulty in sending commands to the projector. If the remote control is not to be used for a long period of time remove the batteries. Replace all batteries at the same time; do not replace one new battery with a used battery. If the batteries have leaked, carefully wipe the case clean and replace with new batteries. Fig. 27 Avoid placing obstructions between the remote control and the infrared sensor at the front of the projector; this will impair the remote control performance. 14 XTRA 9 ON SCREEN MENUS SOURCE SELECTION The Source Selection menu is recalled by pressing the key: 0/AV of the remote control or the Up/Down Arrow key of the keyboard pad. The selected source will be highlighted in yellow. Use Up and Down Arrow keys to browse sources. Right Arrow to select the desired source. Alternatively, use the remote control to directly select the required source (1 to 8). Source Selection 1 2 3 4 5 6 7 8 0 Video S-Video RGBS 15 kHz YCrCb 15 kHz RGBS 32 kHz YCrCb 32 kHz Graphics RGB DVI-D RI2 inputs Video NTSC/60Hz Normal Fig. 28 MAIN MENU To access the main On Screen Display menu, press the Menu key on the keyboard or the key Menu + or Menu - on the remote control (Fig. The main menu is divided into four sections to cover various adjustments in a practical and logical manner. The on-screen menu layout is dependant upon the chosen input signal so various options may not be applicable, i. e. [. . . ] - Ensure that infrared sensors (front and rear of projector) are not exposed to intense light levels. 24 XTRA 12 OPTIONAL ACCESSORIES You can purchase the following optional accessories at your Dealer: - Remote Input Interface with 10 m Cable. Use only original, or SIM2 Multimedia approved, accessories. CAUTION: for ceiling/wall installation, by means of suspension bracket, carefully follow the instructions and safety instructions recommended by the Manufacturer in the bracket's literature. A TECHNICAL SPECIFICATIONS OPTICAL Projection system: DMDTM panel: Brightness uniformity: Contrast ratio: Projection lens: optical engine based on 1 DMDTM HD2+ chip, sealed housing, dusty proof resolution 1280x720 pixel 10% above or below the average > 2800:1 (full On / full Off) zoom, 12 elements AR multilayer coating, motorized focus and zoom, manual elevation 2. 7 (zoom max) - 3. 3 (zoom min) 50-250 inches (diagonal measure) 4/3 and 16/9 1. 8:1 - 2. 5:1 2. 2 - 13. 0 m (7' 3" - 42' 8") 60": 2. 4m - 3. 3m (7' 11" - 10' 10") 80": 3. 2m - 4. 4m (10' 6" - 14' 5") 100": 4. 0m - 5. 5m (13' 2" - 18' 1") Horizontal frequency: Vertical frequency: Video standards : High definition video: Graphic standards : Deinterlacer: Colour temperature: Video processor: ELECTRICAL Input Signals: CVBS on RCA/Phono type connector S-VHS on Mini-DIN connector RGBHV on DB15HD connector RGBS / YCrCb on RCA/Phono type connector DVI-D from 15 to 80 kHz (up to to UXGA format @ 60 Hz) 48-100 Hz automatically selected (PAL B, G, H, I, M, N, 60, SECAM, NTSC 3. 58, 4. 43) ATSC HDTV (480p, 720p, 1080i) VGA, SVGA, XGA, SXGA, UXGA Faroudja chip set, DCDiTM, 3:2 pull down sequence convertion adjustable from 5000 to 9300 degrees K DTI, CTI, comb filter, noise reduction. Sharpness, Y/C delay and NTSC tint adjustments via infrared remote control and via computer through RS232 serial interface via Remote Inputs Interface (optional) and cable with EVC connector 25 Aperture f#: Picture size: Aspect ratio: Throw ratio: (throw distance: picture width) Focus range: Throw Distance: Keystone adjustement: up to 26° (optical: ± 8° digital: ±18°) Remote control: Lamp: Lamp life time: 120 W UHP 8000 hours (average value measured in the laboratory under optimal conditions; it can be sensibly reduced by the unit misusing) Remote inputs: XTRA Low Voltage Power Output: two 12 Vdc output, 100 mA max on jack connectors GENERAL Supply: Frequency: Consumption: Fuse: Dimensions of projector: from 100 to 240 Vac, -10% +6% tolerance from 48 to 62 Hz 180 W max T 3. 15A H, 5 x 20 mm 352 mm x 174 mm x 318 mm (LxHxD) 13"-7/8 x 6"-7/8 x 12"-1/2 (LxHxD) 5. 0 kg (11 lbs) 400 mm x 275 mm x 405 mm (LxHxD) 1' 4" x 11" x 1' 4" (LxHxD) double reinforced carton; expandable anti-shock packaging; gross weight, including accessories: 8 kg (17. 7 lbs); recyclable packaging material ENVIROMENTAL Operation temperature: Transportation temp. : Storage temperature: Humidity: Safety: Transportability: Electromagnetic compatibility: 0 to 35°C (32° to 95°F) -10 to 55°C (14° to 131°F) -10 to 55°C (14° to 131°F) 10% to 90% relative humidity noncondensing EN 60950, UL 60950 desktop equipment EN 55022 Class B EN 55024 EN 61000-3-2 EN 61000-3-3 IEC 68-2-31, IEC 68-2-32 Weight of projector: Packaging and gross weight: Transportation: B DIMENSIONS 352 (13-7/8) 174 (6-7/8) 102 (4) 74 (2-15/16) 318 (12-1/2) unit: mm (inches) 26 XTRA C PROJECTION DISTANCES Follow the table below to determine the optimal projection distance (between the screen and the center of the lens). [. . . ]