User manual SIMPLICITY 870S

[. . . ] After reading this manual, if further assistance is needed, contact your factory authorized sales or service representative. For a list of Sales and Service Centers (SSCs) in your area, Call 1-800-827-3308 or Visit our website at www. slautterback. com NOTE CONCERNING ILLUSTRATIONS: All illustrations within this product manual should be considered as general representations of the parts or assemblies depicted, and should not serve as mechanical drawings, nor be consulted for scope or scale. They are for reference only. Copyright 2000 Slautterback Corporation Table of Contents 1 Safety Precautions for Hot Melt Applicator Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1. 1 Intended Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1. 2 Personal Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] To prevent motor stalling, adjust flow control valve to the minimum flow requirement. 12 Super Squirt SS10G Mark II 19600-133 Rev. C 11/07/00 Copyright 2000 Slautterback Corporation 5. 3 Adjustments 5. 3. 1 Tank Temperature Controller 1. To prevent hot melt degradation, set melt tank temperature to the minimum temperature specified by hot melt manufacturer. To raise melt tank temperature, turn tank temperature controller adjustment shaft [1] clockwise with screwdriver. To lower melt tank temperature, turn adjustment shaft [1] counter-clockwise with screwdriver. The melt tank temperature controller range is 260 °C (500 °F) for one 320° rotation of the adjustment shaft. Allow melt tank temperature to stabilize 30 minutes before adjusting further. Verify temperature on tank thermometer. 4. 5. 6. 5. 3. 2 Hose Temperature Controller Temperature graduations on hose controller reflect approximate hose temperature. Measure inside hose temperature with a pyrometer and bead probe. Hose temperature should be the minimum temperature required for application to prevent degradation of material in the hose and maximize hose life. Verify hose is properly supported so it is not over stressed during use. Minimum bend radius is 20. 32 cm (8 in. ) when hot. Check tank and hose temperatures and adjust as explained in Sections 5. 3. 1 and 5. 3. 2. Procedure Check for foreign material in tank. X Daily X X X X X X X X Monthly As Required* 2. * Extra maintenance required for continuous duty machines. 16 Super Squirt SS10G Mark II 19600-133 Rev. C 11/07/00 Copyright 2000 Slautterback Corporation 7 Troubleshooting Problem Tank does not heat Solutions 1. If switch light fails to illuminate, replace switch. Inspect power-in connections for proper fit. Inspect power wires or power plug at main power source. Check supply voltage to melt unit with voltmeter. Check incoming control voltage to terminal blocks. [. . . ] C 11/07/00 29 9. 4 Motor Assembly Item * 1 2 3 4 5 6 7 8 9 Description (Quantity) Motor group, 38 rpm, 115 VAC, 60/50 Hz Coupling, 15. 88 mm (0. 625 in. ) shaft x 5. 08 cm (2 in. ) Key, 4. 76 mm (0. 1875 in. ) square x 5. 08 cm (2 in. ) Lg. Breaker, 2. 9 Amp Fast Trip Capacitor, 10 µf 370 VAC Spacer, 4 ID x 0. 44 OD x 44. 45 mm (1. 75 in. ) (4) Wire nuts Screw, Shc; 1/4-20 X 3 Lg (4) Washer, split lock, 6. 35 mm (0. 25 in. ) (4) Nut, 1/4-20 hex (4) Part Number 73714-24 70460-4 14475-7 12055A-29 18416-1 14471-4 12277-2 14431-GDT 14451-GA 14441-GA * NOTE: does not include pump On/Off switch/circuit breaker or capacitor. 3 6 9 1, 2 5 4 7, 8 2000353 30 Super Squirt SS10G Mark II 19600-133 Rev. C 11/07/00 Copyright 2000 Slautterback Corporation 9. 5 L2 Handgun Nozzles Item Description (Quantity) L2 Nozzle, 3/16" spacing L2 Nozzle, 1/4" spacing L2 Nozzle, 5/16" spacing L2 Nozzle, 3/8" spacing L2 Nozzle, 7/16" spacing L2 Nozzle, 1/2" spacing L2 Nozzle, 9/16" spacing L2 Nozzle, 5/8" spacing L2 Nozzle, 11/16" spacing L2 Nozzle, 3/4" spacing L2 Nozzle, Extended General Purpose, 1 orifice Part Number 70218-3 70218-4 70218-5 70218-6 70218-7 70218-8 70218-9 70218-10 70218-11 70218-12 70234-1 NOTE: The L2 nozzle spacing dimension equals the space between the two panes of glass in a finished insulated window. © Copyright 2000 Slautterback Corporation Super Squirt SS10G Mark II 19600-133 Rev. C 11/07/00 31 9. 6 Recommended Spares Item Heaters Kit, tank heater, 115 VAC, 400 W Standard Melt Unit Switches Kit, tank controller, 38­232 °C (100­450 °F) Kit, hose controller, 177­232 °C (350­450 °F) Kit, tank overtemperature thermostat, 232 °C (450 °F) Circuit breaker, 115 VAC, 15 A Pump motor ON/OFF switch, 115 VAC, 2 A Pump warmup thermostat 121 °C (250 °F) Kit, tank thermometer Pump Kit, pump, V1-675 Kit, hardware pump, V1 Kit, pump seal, V1 (includes hardware) Motor Motor group, 38/31 rpm, 115 VAC, 60/50 Hz Capacitor, 10 µf, 370 VAC Coupler, pump shaft-motor Key, machine 4. 76 mm (0. 1875 in. ) square x 5. 08 cm (2 in. ) long Pump shaft assembly Kit, idler gear, SS10G Chain assembly, SS10G Wire nuts, medium low temperature L2 Standard Handgun/Hose Assemblies - Capillary Control L2 Handgun/hose, 2. 44 m (8 ft), 232 °C (450 °F), 115 VAC L2 Handgun/hose, 2. 44 m (8 ft), 232 °C (450 °F) 115 VAC 75086-000 75086-200 73714-24 18416-1 70460-4 14475-7 73167-2 79094 73164 12277-2 79048-3 79042 79081 79006 79125-4 79126-450 12015-1 12055-2 79056-1 79014 79005 Description (Quantity) Part Number 32 Super Squirt SS10G Mark II 19600-133 Rev. [. . . ]