User manual SIMRAD OPERATING PANEL OUTLINE SCHEMA REV A

[. . . ] The information contained in this document is subject to change without prior notice. Simrad AS shall not be liable for errors contained herein, or for incidental or consequential damages in connection with the furnishing, performance, or use of this document. Simrad AS Strandpromenaden 50 Box 111 N-3191 Horten Telephone: Facsimile: +47 33 03 40 00 +47 33 04 29 87 YOUR PERFORMANCE AT SEA MAXIMIZING Operator manual Sections 1 System description This chapter provides a brief introduction to the OPERATING PANEL OUTLINE, and defines the main units. Refer to page 1. 2 Display modes This chapter defines the available operational display modes. Refer to page 14. 3 Sonar Operating Panel The main functions of the OPERATING PANEL OUTLINE is controlled by a dedicated keyboard; the operating panel. [. . . ] This mode is used for scientific purposes only, and the sonar will not display any echoes. The menu allows you to change the transmit parameters. Fish Tagging parameters Tilt, page 154 Tx Power, page 160 Sector, page 146 Audio volume, page 99 The Frequency button is visible, but the function is unavailable. The frequency used during this mode is fixed to 26536 kHz. The Help button opens the on-line help. Related topics Fish Tagging, mode description, page 29 72 850-164186 / Rev. D Menu description Temporary menus The Temporary menus are those selected from the active menus. They are also shown with vertical tabs on the right side of the menu, and can easily be selected by the trackball and the Select button. The Temporary menus must however be removed manually using the Close button in the bottom of menu. All Temporary menus have access to on-line help through a Help button. Temporary menus Cosmetics, page 74 Store/Recall, page 75 Test, page 76 Sort Modes, page 78 850-164186 / Rev. D 73 Simrad OPERATING PANEL OUTLINE Cosmetics The Cosmetics menu is activated by pressing the Cosmetics button in the Display menu. It provides access to various parameters controlling the appearance of the sonar picture. All the functions - except Track history - are on/off buttons. Cosmetic parameters Slant Range / True Range, page 147 Bearing Card, page 57 Compass Card, page 58 Distance Rings, page 57 VRM (Variable Range Marker), page 58 Bow Marker, page 59 Track History, page 156 Minute Marker, page 59 Wind Marker, page 57 Vertical Ring, page 58 Depth dividers, page 59 The Close button closes this menu. The Help button opens the on-line help. 74 850-164186 / Rev. D Menu description Store/Recall The Store/Recall menu is activated by the Store/Recall button in the Setup menu. The Store/Recall menu is used to store single display pictures or a sequence or pictures. The Help button opens the on-line help. Related topics Message bar, page 126 About, page 97 850-164186 / Rev. D 77 Simrad OPERATING PANEL OUTLINE Sort Modes The Sort Modes menu is activated by the Sort Modes button in the Setup menu. The Sort Modes menu is used to select the display modes to be activated by the four Mode buttons on the Sonar Operating Panel. The four upper display modes in this menu will always be the four modes selectable by the four Mode buttons in the order they are sorted. In order to sort the modes, select the actual mode and use the Move Up and Move Down buttons to place it in the wanted position. When the modes are organized in the requested order, press the Apply button to store the information. Related topics Mode buttons, Operator Panel, page 34 Mode buttons, page 128 78 850-164186 / Rev. D Menu description Pop-up menus The pop-up menus are accessed using the View and Object buttons on the Sonar Operating Panel, or the middle and right mouse buttons if an optional mouse is installed. Each button will present a small menu, and it appears at the cursor's current location. To make a selection, use the trackball and the Select button, or the mouse. Pop-up menus View, page 80 Object, page 82 Related topics View and Object buttons, page 37 850-164186 / Rev. D 79 Simrad OPERATING PANEL OUTLINE View pop-up The View pop-up menu is accessed using the View button over the trackball on the Sonar Operating Panel or the middle mouse button if an optional mouse is installed. When activating the pop-up menu in the Catch Data view, it will display the following reduced menu. View pop-up parameters Set New Display Centre - When this function is selected, the new display centre is moved to the cursor's position where the View menu was activated. Ship To Centre - When this function is selected, the own ship symbol is moved to the centre of the view. Zoom - The zoom function magnifies an area of the display by positioning the cursor in its centre and pressing the Zoom button. The zoom button works as a toggle switch for on/off of the zoom function. Erase Echoes - When this function is selected, all echoes displayed on the sonar view will be deleted. [. . . ] Check with the hand crank to ensure that the motor brake is engaged. Remove the hand crank from the stub shaft, and mount it in its storage position in the Motor Control Unit. Press the black button marked 1 on the motor overload switch S301. 7 8 180 850-164186 / Rev. D On-board maintenance Air bleeding To avoid damage to the transducer by transmitting in air inside the trunk, the air bleeding system must be checked after the ship has been docked. 1 2 3 4 Close the air bleeding cock on top of the trunk flange and dismount the pipe. [. . . ]