User manual SIMRAD OUTLINE DIMENSIONS ES120-7CD SCHEMA REV A

[. . . ] to either repair or replace any unit/part that fails within the limits of the Warranty Policy. The Warranty Policy is only valid on new equipment Replacement of parts, components, and/or PCB Boards during a warranty repair does not extend the original warranty period. Consumable Materials: · Consumable materials, such as lamps, fuses, o-rings, gaskets and batteries, shall not be replaced free of charge. Kongsberg Simrad Mesotech Ltd. Port Coquitlam, BC - Canada 974-25007001/2. 0 Page 2 SL 30/35 Hull Sonar Operators Manual List of Contents Warranty Service: · Warranty service is available worldwide through authorized Kongsberg Group Companies, Simrad Distributors, Dealers or Agencies. When requesting warranty service, you must supply the following information: 1. [. . . ] Stabilization control enables the automatic tilt angle adjustment with the overall Pitch and Roll angle of the head. If the head is equipped with pitch and roll sensors, then prior to each acoustic ping the head reads its pitch and roll angle, calculates the offsets required to maintain the transducer at its desired angle and changes the tilt angle to compensate. 4. 59. 6. 2 Head Settings: Transmit The Head Settings: Transmit page is used to determine how the head transmits and receives. Kongsberg Simrad Mesotech Ltd. Port Coquitlam, BC - Canada 974-25007001/2. 0 Page 4. 54 SL 30/35 Hull Sonar Operators Manual Menu and Software Description The Uplink Baud Rate control is used to set the rate at which data is sent from the head to the surface. You will normally want to set this control to as high a rate as your system will support without generating too many errors. When Compression is set to On, the color depth of the sonar image will be an eighth of its maximum through a reduction in the signal amplitude resolution. This however, increases the uplink speed of the sonar data, thereby increasing system performance. The option can usually be set to On due to negligible effect of the loss in color depth. The Pulse Length control can be used to set the desired transmit pulse length on heads that support this feature. Generally, a shorter pulse length will give a sharper image but with reduced range. By default, the system adjusts the pulse length at different range and display mode settings according to the selection of the Optimize resolution or Maximize Range. The automatic selection of the pulse length can be disabled by clicking the Manual Setup box. Note that the screen resolution must be able to support a minimum of 960x960 pixels, otherwise the system automatically displays the sonar data in low resolution, even if collected in high acquisition resolution. 4. 59. 6. 3 Head Settings: Info This page shows the calibration results as well as some hardware information about the sonar head. Kongsberg Simrad Mesotech Ltd. Port Coquitlam, BC - Canada 974-25007001/2. 0 Page 4. 56 SL 30/35 Hull Sonar Operators Manual Menu and Software Description The Calibration results reflect the positional accuracy of the optical sensors in the rotary scanning heads. Calibration data is not displayed for non-rotation heads such as altimeters The optical sensors are used to estimate the current rotational angle of the transducer within the dome. The CW and CCW columns are the detected ClockWise and CounterClockWise position of the optical sensors with respect to the 0 degree reference marker on the head. Theoretically the CW and CCW values should be the same and at perfect 0, 400, 800 and 1200 (corresponding to 0, 90, 180 and 270 degrees respectively). However, due to optical sensor mounting errors the positions do not match the perfect counts. Also due to the optical view field of the sensors, the CW and CCW values are not equal. Variation between the CW and CCW at each quadrant should be less than 20. Positional errors of each quad from its perfect value should be less than 35. Values outside these limits should be reported to Kongsberg Simrad Mesotech or its representatives. Example: Ref 0 90 CW 0 390 CCW 1596 415 normal abnormal, but operable Kongsberg Simrad Mesotech Ltd. [. . . ] If the text "Everyone" does not appear as shown bellow, then press the "Add" button. 6. 7. Pressing the "Add" button will pop up the "Add Users and Groups" dialog box as follows. 6. 8. 6. 9. 6. 10. Select "Everyone" entry from the list of names and press the "Add" button. Press "OK" to accept the selection. You should now see "Everyone" in the "Registry Value Permissions" dialog box. [. . . ]