User manual SINGER 321C DATASHEET

[. . . ] 19 USER MAINTENCE Instructions Cleaning and care . 28 INSTALLATION INSTRUCTIONS Installation . 39 2 Guide to the machine Guide to the machine 1 Supply cable 2 Cold water pressure hose 3 Flexible drain hose, with detachable swivel elbow 4 Detergent dispenser drawer 5 Control panel 6 Drum door 7 Panel for access to lint filter and drain pump 8 Four height-adjustable legs 3 Guide to the machine Detergent dispenser drawer Compartment i - for the pre-wash. Compartment p (with lid) - for fabric softener or starch. b "Door" button; opens the drum door. c "ON/OFF" button; Turns the machine on and off or interrupts a program. [. . . ] If spinning is not desired, turn the program selector to "Drain". "Water plus" Slightly increases the water level, best used; ­ For particularly delicate fabrics in addition to the "Gentle wash" option. ­ In hard water areas, if additional water is required for dispensing the detergent. ­ In soft water areas to enhance washing and rinsing results. ­ For people who are skin sensitive to detergents. The "Water plus" option is available in the following programs: ­ The wash and rinse cycles for COTTONS. ­ The wash cycle for PERMANENT PRESS. 18 Changing the program sequence Changing the program sequence To cancel a program: ^ Turn the Program Selector to the "Finish/Start" position. During operation, it is possible to: ­ manually omit one or more program stages or ­ manually repeat one or more program stages. To interrupt a program: ^ Turn the machine off. To re-start a program, turn the machine on again. To change an incorrectly selected program: ^ Turn the Program Selector to "Finish/Start". When only the "On" LED is lit, a new program can be selected. To change a program when the Child Safety Feature has been set, see Programmable functions". To omit a program stage: ^ Turn the Program Selector to "Finish/Start". As soon as the program sequence indicator lamp for the stage you wish stops flashing: ^ turn the Program Selector to the desired program. To repeat a program stage: a program stage must end before it can be repeated: ^ Turn the Program Selector to "Finish/Start". When only the "On" LED is illuminated: ^ Re-select the program. Clean the filter under running water and carefully remove any large particles. ^ Replace the filter and seal and reconnect the hose. Slowly turn on the valve and check for leaks. ^ Using needle nose pliers, withdraw the plastic filter by pulling on the bar (see illustration). Rinse under water to clean, and then replace. The two filters - one at the pressure hose/valve connection and one at the inlet connection to the solenoid valve - must not be removed. 23 Problem solving guide Problem solving guide Any work done on the electrical components of this appliance should only be performed by a qualified and trained person in accordance with all local and national codes and regulations. Unauthorized repairs may result in personal injury and damage to the machine. The following are minor problems that can be corrected without contacting the Technical Service Department. Check q warning lamp flashes Drainage fault: ^ Check if the lint trap is clogged. Clean the trap and pump impeller (see , , Cleaning and Care"). ^ Check whether the drain hose is kinked or clogged. The warning lamp will go out when the Program Selector is turned to the , , Finish/Start" position. [. . . ] Ask for a NEMA 14-30 R receptacle. Warning Improper connection of the equipment-grounding conductor can result in the risk of electric shock. Check with a qualified electrician if you are in doubt as to whether the appliance is properly grounded. Do not modify the plug provided with the appliance; if it will not fit the outlet, have the proper outlet installed by a qualified electrician. "EASY INSTALLATION KIT" If you don't have a dedicated 4 wire, 120 V/240 V (208 V), 15 Amp line for this appliance, but you have a 3 or 4 wire, 240 V (208 V), 30 Amp line, you can use an optional "Easy Installation Kit", which will allow you to connect this appliance to that line. For more information on the electrical connection and the "Easy Installation Kit" please contact ­ the nearest Miele Technical Service Department. 34 Programmable functions Programmable functions The following additional functions can be programmed into the machine if desired: C Program Lock (Child safety feature) When activated, the washing machine will ignore any changes made after the first three minutes of operation. [. . . ]