User manual SINGER 6212

[. . . ] Chapter-Page 1 1. 01 1. 02 1. 03 1. 04 1. 05 1. 05. 01 1. 05. 02 1. 06 2 3 3. 01 3. 02 3. 03 3. 04 4 5 5. 01 5. 02 5. 03 5. 04 6 7 7. 01 7. 02 7. 03 7. 04 7. 05 7. 06 7. 07 7. 08 7. 09 8 8. 01 8. 01. 01 Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Regulations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 General notes on safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Safety symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] For packing and transportation reasons the table top is in the lowered position. The table height is adjusted as described below. 8. 01. 01 Adjusting the table height 1 1 2 Fig. 8 - 01 q Loosen screws 1 and 2 and set the table at the required height. q Set the required pedal position and tighten tighten screw 2. 8-1 Installation and commissioning 8. 01. 02 Tensioning the v-belt q Loosen nuts 1. q Tension v-belt by adjusting bracket 2. If a different motor is used, please refer to the instruction manual of the motor manufacturer. 2 cm 1 2 Fig. 8 - 02 8. 01. 03 Fitting the upper belt guard 6 If a large balance wheel is in use, break off corner 1 of belt guard part 3. q q q q Screw stop piece 2 onto belt guard part 3. Screw on belt guard part 3 with screws 4. Screw on belt guard part 5 with screws 6. Secure belt guard part 7 to the table top using woodscrews 8. 4 2 5 6 8 4 3 7 8 8 Fig. q Push needle 2 fully in (the long needle groove must face to the left). q Tighten screw 1 again. . 1 2 Fig. 9 - 01 The choice of needle depends on the version of the machine and the sewing thread and material in use (see Chapter 3, Specifications). 9-1 Setting up 9. 02 Inserting the needles on the SINGER 6212 Switch off the machine!Danger of injury due to unintentional starting of the machine!q Set needle bar at top position and loosen screws 1. q Push needles 2 fully in (the long groove of the left needle must face to the right and that of the right needle to the left). 9 - 02 The choice of needle depends on the version of the machine and the sewing thread and material in use (see Chapter 3, Specifications). 9-2 Setting up 9. 03 Winding the bobbin thread, regulating the winder tension 4 - + 6 3 1 2 5 Fig. 9 - 03 q Place an empty bobbin 1 on winder spindle 1. 9-03 and wind the thread a few ttimes clockwise around bobbin 1. q Engage the bobbin winder by pressing spindle 2 and lever 3 simultaneously The bobbin is wound during sewing. q The tension of the thread wound onto bobbin 1 is set on knurled screw 4. q The bobbin winder will stop when sufficient thread is wound onto bobbin 1. [. . . ] On the SINGER 6212 thread-catcher drive linkage 1 must have a length of 128 mm, less half of the needle gauge. On the SINGER 1295, thread catcher drive linkage 1 must have a length of 128 mm 2. When the threa trimmer is in its resting position there must be a clearance of about 1 mm between plunger 5 and lever 6. 128 mm 2 2 6 1 1 mm 5 3 4 Fig. 11 - 22 q Turn thread-catcher drive linkage 1 (nuts 2) to adjust it according to Requirement 1. [. . . ]