User manual SINGER 71-30 TO 70-47

[. . . ] Raise pins 7 and place a spool of thread on one of them. Place a bobbin on bobbin winder 8 so that pin H enters slot G. Pass the thread from the spooi around bobbin tension stud 3, wind it around the bobbin a few times and push the bobbin to the right for winding. When the bobbin is full push it to the left and remove it. [. . . ] located at the back of the presser ng foot. Pull the work out Raise the sewi the of the machine toward the back. Draw r slot and pull them threads into the cutte downwards to cut them. Regulating the stitch length the The stitch length is set at mark G on th control. The numbers stitch leng indicate the length in mm. H shows how to set the stitc for sewing stretch stitches on control models 806 and 807. /- N 7 \ 8 cr< _40 o CD N (CD < -- QN CD 0Ocl) CD £ tT CD CD D3 --1 0. 0 CX) -- t3- CD T CD (0 CD 0 a g o. OlD a o. 0 OlD CD' 00. 0<D2. = 0 CD 0 . . (CD (CD CD :3- IG) II --:3 O. -uo 7m 0 CD 000(DCD D. ;:y;; D_ CD -- -. --Z CD 3 CD <DO) CD 0. 3 1J 0. -, 5 3 CD 300 -- CD 0 (DCD0CD3 -- CD g 0 :jcG 0 :3 0D ;:: -- 5. 2 c -ä 00 03 CD P. . Selecting utility stitches on models 802 to 807 ible are The various utility stitches poss sector by black letters in the red indicated machine and of the stitch panel on the explained on page 11. h selector dial The utility- and stretch-stitc d in a clockwise 5 should only be turne direction. corresponding Turn dial 5 until the letter is in the centre of to the stitch you want Fig. the cutout at the bottom (see to the Set stitch length selector 11 zigzagreq uired stitch length, and the to the required zigzaq-width. Insert the pin of the foot in hole K and attach the foot so that it rests against its stop. Release bracket M so that it bears against screw N. Tighten screw L. Buttonhole settings On models 802 to 807 set utilitystitch dial 5 to B. Push lever 6 to buttonhole symbol G and let it snap into position. Set the stitch density in the buttonhole sector of stitch length control 11. Move zigzag-stitch lever 4 to the right for straight stitching. J): place it over the rear lug of the foot, pull it taut and clamp it in front lug K. As you sew, arrow L moves along scale M. This determines the buttonhole length. 16 a) . 0 0) -- Ct) CC) 4 --: 0) > . 00) -- - 0 E >, a) -- :5> a) S. ; C - 0) 0 0) tJ C a) = 0 a) . 3 = . g . 5 Z :3 a) ci) --a) (0. 0 (0 1) a) a). 0 0 > C D) 0> >Q CC) C `U a) > 3--4i 0 U) c" 03 CC) - E :5 ci :300 (0 U) 00) C1) - 4 -a) -- -C C o :3 >-. Ccii a) . 0 . 0 -- 0) . 0 a) a)a) -- (0 a) ` 0) 03 - . 5 E +. ` C 0 0. -- -- o C') :3 a)) a) = a) --- 0 -- C ±CI) -- ? 0 . a)j o'2 C -- G) . c C DO . 0 o . 22-o 5 CC) C -- C 0 g `-- E >-z >0)0)> 0 C C `2 > a) (i)cL-- `t) -0 > _s > C a) 0 a) 00 a) a) CI) C - aS 55 55 55 cc) _5 -- as -- a) C I e c') Fitting the detachable workplate on models 800, 802 and 806 The foot control receptacle of these models also serves as a detachable workplate. Turn the receptacle round and fit it to the machine so that its two haoks enter the two holes in the machine base. [. . . ] Clea sewing hook and the machine round the feed with a soft brush (Fig. mainte Do not oil the machine as it is All you have to do is put a nance-free. now and drop of oil in the hook raceway then (Fig. J). 19 Trouble shooting Cause: 1. [. . . ]