User manual SINGER 78-2

[. . . ] Connecting the water inlet hose • To a suitable cold water connection point: before attaching the hose, run the water until it is perfectly clear so that any impurities that may be present in the water do not clog the appliance; after performing this operation, screw the inlet hose tightly onto a tap with a ¾ gas threaded connection. • To a suitable hot water connection point: your dishwasher may be supplied with hot water from the mains supply (if you have a central heating system with radiators) provided that it does not exceed a temperature of 60°C. Screw the hose to the tap as described for connection to a cold water supply. If the inlet hose is not long enough, contact a specialist store or an authorised technician (see Assistance). [. . . ] if it is pressed again the option will be deselected. The EXTRA DRYING option increases the duration of the wash cycle. Confirm the selection using the STAR/PAUSE button; the symbol will stop flashing and the countdown will begin. The text “Start in…” will be displayed, the selected delay time will flash and the START/PAUSE button will remain lit in a fixed manner. When the set time has elapsed, a long beep sounds, the DELAYED START indicator light switches off and the wash cycle begins. To deselect the DLEAYED START option, press the DELAYED START button repeatedly until the text OF. The Delayed Start function cannot be set once a wash cycle has been started. SELFCARE WASH CYCLE This disinfecting wash cycle deep cleans the inside of the dishwasher, thereby reducing the formation of bad odours. WARNING The SELFCARE wash cycle should be performed as part of your dishwasher maintenance routine, using special singledose products (follow the instructions on the packaging) while the dishwasher is EMPTY. Table of options* A Delayed Start Auto Super wash Normal Daily A 60’ Soaking Eco 50°C Speed 25’ Crystals Baby Cycle Auto Duo Wash Ultra Intensive Special Guest Self Care Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes B Half Load Yes Yes Yes Yes Yes No Yes No No Yes Yes No C Tabs Yes Yes Yes No Yes Yes Yes No Yes Yes No No D Extra Dry Yes Yes No No Yes NO Yes No Yes Yes Yes No E Shor Time Yes Yes No No No No No No Yes No No No F Good Night No Yes No No Yes No No No No No No No ShorTime* option This option can be used to reduce the duration of the main wash cycles while maintaining the same washing and drying performance levels. After selecting the wash cycle, press the ShorTime option button; the illumination of the corresponding indicator light followed by a short beep indicates its selection. Note for Test Laboratories: for information relating to comparative EN testing conditions, please send an email to the following address: ASSISTENZA_EN_LVS@indesitcompany. Com 9 Rinse aid and refined salt EN Only use products which have been specifically designed for dishwashers. do not use table salt or industrial salt , or washing up liquid. Follow the instructions given on the packaging. If using a multi-functional product it is not necessary to add rinse aid; however, we recommend that you add salt, especially if you live in an area where the water is hard or very hard. Follow the instructions given on the packaging. - Press the DELAYED START button (levels 1 to 5) or the HALF LOAD button (levels 5 to 1) repeatedly, until the desired hardness level has been reached (1-2-3-4-5*, see hardness table). You will be able to scroll through a maximum of 5 levels. - To exit the function, wait approximately 30 seconds or press another option button, or switch off the machine using the ON/OFF button. Even if using multi-functional tablets, the salt dispenser should still be filled. If you do not add salt or rinse aid, the LOW SALT* and LOW RINSE AID* indicator lights remain lit. [. . . ] The crockery has not been d ried p ro p erl y. € T he rinse aid has be en use d up or th e dosag e is too low (see R inse a id and salt). • T he rinse aid disp e nser se tting is not high eno ugh. T he wash cycle is too gentle (see W ash cycles). [. . . ]