User manual SINGER BRILLIANCE 6180

[. . . ] 5500 6199/6180/6160 INSTRUCTION MANUAL MANUEL D’INSTRUCTION MANUAL DE INSTRUCCIONES F-1 “IMPORTANT SAFETY INSTRUCTIONS” “When using an electrical appliance, basic safety precautions should always be followed, including the following. € “Read all instructions before using this sewing machine. € “DANGER--To reduce the risk of electric shock:” “WARNING- To reduce the risk of burns, fire, electric shock, or injury to persons: ” 1. Close attention is necessary when this sewing machine is used by or near children. [. . . ] ž Tacking stitch is made automatically after buttonhole stitch is completed. It is not necessary to push the reverse/tacking stitch button. ž Move bobbin winder to left when it is not used. 29 REVERSE OPERATION BUTTON BOUTON D'OPÉRATION DU POINT DE MARCHE ARRIÉRE INTERRUPTORES DE FUNCIONAMIENTO DUAL PURPOSE REVERSE/TACKING STITCH BUTTON BOUTON DOUBLE USAGE POINT MARCHE ARRIÉRE /POINT D'ARRÊT INTERRUPTOR DE COSTURA HACIA ATRÁS/REMATE * Reverse stitch function for straight and zigzag stitches (　 ) Reverse sewing is carried out while the reverse stitch button is pushed. The machine will continue to sew in reverse as long as the reverse button is pressed. Reverse stitch button Bouton du point de marche arrière * Tacking stitch function for tie-off of other stitches ( ) The sewing machine makes 4 tiny tacking stitches to tie off the sewing on all patterns except straight, zigzag and buttonhole stitches. The position of the tacking stitches will be at the exact spot in the pattern where the reverse/tacking stitch button is pushed. NOTE: This function is very useful for tying off the sewing pattern to avoid raveling at the start and end of sewing. 100 stitch model 80 stitch model 60 stitch model QUICK REFERENCE TABLE OF STITCH LENGTH AND WIDTH TABLEAU DE RÉFÉRENCE RAPIDE DES LONGUEURS ET LARGEURS DE POINTS CUADRO DE REFERENCIA RÁPIDA DE LARGO Y ANCHO DE PUNTADA NEEDLE POSITION POSITION D’AIGUILLE POSICIÓN DE AGUJA LENGTH LONGUEUR (mm) LARGO AUTO AUTO AUTO MANUAL MANUEL MANUAL AUTO AUTO AUTO CENTER CENTRE CENTRO MANUAL MANUEL MANUAL LEFT - RIGHT GAUCHE - DROIT IZQUIERDA - DERECHA 00 00 00 2. STITCH POINT PUNTADA 100 stitch model 80 stitch model 60 stitch model STITCH POINT PUNTADA 100 stitch model 80 stitch model AUTO MANUAL AUTO MANUAL AUTO MANUEL AUTO MANUEL AUTO MANUAL AUTO MANUAL 5. STITCH POINT PUNTADA 100 stitch model 80 stitch model 60 stitch model STITCH POINT PUNTADA 100 stitch model 80 stitch model AUTO MANUAL AUTO MANUAL AUTO MANUEL AUTO MANUEL AUTO MANUAL AUTO MANUAL 3. STITCH POINT PUNTADA 100 stitch model 80 stitch model 60 stitch model STITCH POINT PUNTADA 100 stitch model 80 stitch model AUTO MANUAL AUTO MANUAL AUTO MANUEL AUTO MANUEL AUTO MANUAL AUTO MANUAL 60 stitch model ─ 47 WIDTH LENGTH LARGEUR (mm) LONGUEUR (mm) ANCHO LARGO PATTERN No. STITCH POINT PUNTADA 100 stitch model 80 stitch model 60 stitch model STITCH POINT PUNTADA 100 stitch model 80 stitch model AUTO MANUAL AUTO MANUAL AUTO MANUEL AUTO MANUEL AUTO MANUAL AUTO MANUAL 60 stitch model ─ 55 WIDTH LENGTH LARGEUR (mm) LONGUEUR (mm) ANCHO LARGO PATTERN No. NOTE: Based upon the weight of the fabric, slight “fine tuning” of the tension may be desired. Pull both threads under the presser foot toward the back of the machine, leaving about 6” (15cm) clear. Place the fabric under the presser foot and lower the presser foot lifter. Turn the hand wheel toward you (counter-clockwise) until the needle enters the fabric. Guide the fabric gently with your hands. When reaching the edge of the material, stop the sewing machine. NOTE: The Needle Plate has both Metric and Inch Markings as an aid for guiding your fabric when sewing a seam. First turn the handwheel toward you (counter-clockwise) until the needle is at its highest position. Raise the presser foot, draw materials to the rear and cut off excess thread with the thread cutter located on the bottom of face cover as shown. [. . . ] Remove the shuttle race cover and shuttle. Clean the feed dogs and shuttle area with the lint brush. NOTE:Put a drop of sewing machine oil on the center pin of the shuttle and shuttle race as indicated by the arrows. Be sure the shuttle race forms a half moon on the left side of the machine. [. . . ]