User manual SITECOM 300N WIRELESS ROUTER WL-582

[. . . ] WL-340/WL-341 Wireless Broadband router (802. 11bgn draft 2. 0) User Manual Revision: 1 TABLE OF CONTENTS 1 2 3 4 5 6 7 8 9 KEY FEATURES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 PACKAGE CONTENTS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 PRODUCT LAYOUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 NETWORK + SYSTEM REQUIREMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] If you want to use the PIN code, you have to know the PIN code of the wireless client and switch it to WPS mode, then fill-in the PIN code of the wireless client through the web configuration interface of the wireless router. WPS Check the box to enable WPS function and uncheck it to disable the WPS function. 30 WPS Current Status If the wireless security (encryption) function of this wireless router is properly set, you'll see a `Configured' message here. Otherwise, you'll see `UnConfigured'. Self Pin Code This is the WPS PIN code of the wireless router. You may need this information when connecting to other WPS-enabled wireless devices. SSID This is the network broadcast name (SSID) of the router. Authentication Mode It shows the active authentication mode for the wireless connection. Passphrase Key It shows the passphrase key that is randomly generated by the wireless router during the WPS process. You may need this information when using a device which doesn't support WPS. WPS via Push Button Press the button to start the WPS process. The router will wait for the WPS request from the wireless devices within 2 minutes. WPS via PIN You can fill-in the PIN code of the wireless device and press the button to start the WPS process. The router will wait for the WPS request from the wireless device within 2 minutes. 31 12 Firewall Settings The Broadband router provides extensive firewall protection by restricting connection parameters, thus limiting the risk of hacker attacks, and defending against a wide array of common Internet attacks. However, for applications that require unrestricted access to the Internet, you can configure a specific client/server as a Demilitarized Zone (DMZ). Note: To enable the Firewall settings select Enable and click Apply 32 DMZ If you have a client PC that cannot run an Internet application (e. g. Games) properly from behind the NAT firewall, then you can open up the firewall restrictions to unrestricted two-way Internet access by defining a DMZ Host. The DMZ function allows you to re-direct all packets going to your WAN port IP address to a particular IP address in your LAN. The difference between the virtual server and the DMZ function is that the virtual server re-directs a particular service/Internet application (e. g. FTP, websites) to a particular LAN client/server, whereas DMZ re-directs all packets (regardless of services) going to your WAN IP address to a particular LAN client/server. Enable DMZ Enable/disable DMZ Public IP Address The IP address of the WAN port or any other Public IP addresses given to you by your ISP Client PC IP Address Enter the IP address of a particular host in your LAN that will receive all the packets originally going to the WAN port/Public IP address above. Click <Apply> at the bottom of the screen to save the above configurations. 33 Denial of Service (DoS) The Broadband router's firewall can block common hacker attacks, including Denial of Service, Ping of Death, Port Scan and Sync Flood. If Internet attacks occur the router can log the events. SPI and Anti-Dos firewall protection blocks basic hacker attacks (DOS, Sync flood, port scan) RIP defect Allows the user to choose if the router should respond to other RIP compliant devices. Discard Ping to WAN interface The router's WAN port will not respond to any Ping requests. Stateful packet inspection allows the user to manually determine which packets should be scanned. Specify your SMTP and POP3 servers, user name, and password. Connection Policy Enter the appropriate values for TCP/UDP sessions as described in the following table. 34 Access You can restrict users from accessing certain Internet applications/services (e. g. Internet websites, email, FTP etc. ), Access Control allows users to define the traffic type permitted in your LAN. You can control which PC client can have access to these services. Deny If you select "Deny" then all clients will be allowed to access Internet accept for the clients in the list below. Allow If you select "Allow" then all clients will be denied to access Internet accept for the PCs in the list below. Filter client PCs by IP Fill in "IP Filtering Table" to filter PC clients by IP. Add PC You can click Add PC to add an access control rule for users by IP addresses. Remove PC If you want to remove some PCs from the "IP Filtering Table", select the PC you want to remove in the table and then click "Delete Selected". [. . . ] To communicate with the Router, the NMS must first submit a valid community string for authentication. Note: Up to five community names may be entered. Note: Up to five community names may be entered. Trap Specify the IP address of the NMS to notify when a significant event is detected by the agent. When a trap condition occurs, the SNMP agent sends an SNMP trap message to any NMS specified as a trap receiver. IP Address Traps are sent to this address when errors or specific events occur on the network. [. . . ]