User manual SITECOM WIRELESS INTERNET SECURITY CAMERA 150N WL-405

[. . . ] Wireless Network IP-Camera 150N WL-405 Full Manual Table of Contents 1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] VGA resolution provides more details than QVGA and QQVGA, but requires more network bandwidth. Video Quality Specify video encoding quality of MJPEG video encoder. There are five levels of video quality from highest to lowest. Higher video quality provides better video quality, but requires more network bandwidth. Video Frame Specify video refresh rate of MJPEG video encoder. Higher video Rate refresh rate provides more details about motion, but requires more network bandwidth. CAUTION: Choosing a low frame rate will save bandwidth, but may not be able to capture every motion if the object that IP camera points to is moving fast. Click `Apply' to save settings and make the new settings take effect. 3. 6 Motion Detection Basic Settings 3. 6. 1 The motion detection function makes this IP camera become your non-stop guard. You don't have to waste all the time monitoring the images from the camera, and camera will detect all motions for you. Once motion is detected, a captured image will be sent to you by Email or via FTP. You can access this menu by clicking `Video Setup' on the top of web management interface, and opening the 'Motion Detection' tab. The descriptions of Item Motion Detection Enable Detection Interval every setting in this menu will be given below: Description Select `Enable' to start motion detection, and select `Disable' to disabled it. Specify the time interval between two motion detections in seconds. If a motion is detected after last detection time, and before next detection time, nothing will be send by Email or via FTP. Please specify a time interval that suites your need. If the time interval is too long, you may not be able to know what is happened between time interval; if the time interval is too short, you may receive too much unnecessary images, and consumes too much disk Mail snapshot E-Mail Subject Send snapshot file to FTP storage spaces on Email and / or FTP server. Select `Yes' to send a picture to the Email address you specified in `E-Mail & FTP' menu when a motion is detection, and select `No' to disable this function. Set the subject of Email being sent here. This will help you to distinguish the Email sent by this IP camera from others. Select `Yes' to send a picture to the FTP server you specified in `EMail & FTP' menu when a motion is detection, and select `No' to disable this function. Click `Apply' to save settings and make the new settings take effect. 3. 6. 2 Setup Motion Detection Regions If you only want to be notified when motion is detected in certain area of captured image, you can use this function and motions outside of motion detection region will be ignored, so you won't receive too much `useless' notifications. This IP camera supports up to 3 motion detection regions. To setup detection region, Please use your mouse to drag and resize motion detection regions marked as `Region1', `Region2', and `Region3' (which appear as yellow, green, and red squares on the image): Motion detection region settings can be found at the bottom of this page: The descriptions of every setting in motion detection menu will be given below: Item Description Region1 / Check the box to enable / disable a certain motion detection area. Region2 / Region3 Sensitivity Control the detection sensitivity of motion detection of respective motion detection region. [. . . ] If you're connecting this camera from Internet, it could be caused by a slow Internet connection, and it's not a problem caused by camera. However, when the network connection is slow, you should use lower frame rate / resolution. Adjust the antenna if you're using wireless connection. The antenna should be perpendicular to the ground to get best reception, and the distance between IP camera and computer / wireless access point should not be too far. [. . . ]