User manual SKIL 6092

[. . . ] ) ME77 GB F D NL S DK N FIN E P I H CZ TR INSTRUCTIONS INSTRUCTIONS HINWEISE INSTRUCTIES INSTRUKTIONER INSTRUKTION ANVISNING OHJEET INSTRUCCIONES INSTRUES ISTRUZIONI LERS POKYNY KILAVUZ page 10 page 12 Seite 16 bladz. 41 oldal 44 strana 47 sayfa 50 PL RU UA GR RO BG SK HR SRB SLO EST LV LT INSTRUKCJA O INSTRUCIUNI KA3A POKYNY UPUTE UPUTSTVA NAVODILA INSTRUKCIJA INSTRUKCIJA strona 53 56 60 64 pagina 68 71 strana 75 stranica 78 stranica 81 stran 83 lappuse 89 puslapis 93 KASUTUSJUHEND leheklg 86 www. skileurope. com SKIL Europe BV - Konijnenberg 60 4825 BD Breda - The Netherlands 09/07 2610398120 1 6092 550 W 1, 9 kg 0-3000 16 12 0-48000 p/min 2 G E 3 F H C D B A 4 5 2 6 7 A C A C 8 9 0 3 ! 4 @ K J MAX. 200 mm # L 2 4 5 1 3 5 $ L 2 3 1 4 5 % 6 ^ & * J N M K 7 ( HSS PHILLIPS POZIDRIV SLOTTED ) 8 ACCESSORIES 2610073400 In Deutschland nicht lieferbar 2610397119 2610397256 2, 3, 4, 5, 6 mm 1. 5, 2, 2. 5, 3, 3. 5, 4, 4. 5, 5, 5. 5, 6, 8 mm 4, 5, 6, 6, 8 mm 4, 5, 6, 8, 10 mm 4, 5, 6, 8, 10 mm 3, 4, 5, 6, 8 mm 9 GB Hammer drill INTRODUCTION 6092 This tool is intended for hammer drilling in brick, concrete and stone as well as for drilling in wood, metal, ceramic and plastic; tools with electronic speed control and left/right rotation are also suitable for screwdriving and thread cutting Read and save this instruction manual 3 TECHNICAL SPECIFICATIONS 1 TOOL ELEMENTS 2 A B C D E F G H Switch for on/off and speed control Button for switch locking Wheel for maximum speed control Switch for changing direction of rotation Switch for selecting drilling function Auxiliary handle Dust filter system Ventilation slots SAFETY GENERAL SAFETY INSTRUCTIONS WARNING!Read all safety warnings and all instructions. [. . . ] Use of the power tool for operations different from those intended could result in a hazardous situation. 5) SERVICE a) Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained. SAFETY INSTRUCTIONS FOR HAMMER DRILLS Wear ear protectors with hammer drills (exposure to noise can cause hearing loss) Use auxiliary handles supplied with the tool (loss of control can cause personal injury) Avoid damage that can be caused by screws, nails and other elements in your workpiece; remove them before you start working Always keep the cord away from moving parts of the tool Secure the workpiece (a workpiece clamped with clamping devices or in a vice is held more securely than by hand) When you put away the tool, switch off the motor and ensure that all moving parts have come to a complete standstill Use completely unrolled and safe extension cords with a capacity of 16 Amps (U. K. 13 Amps) In case of electrical or mechanical malfunction, immediately switch off the tool and disconnect the plug SKIL can assure flawless functioning of the tool only when original accessories are used Use only accessories with an allowable speed matching at least the highest no-load speed of the tool This tool should not be used by people under the age of 16 years Use suitable detectors to find hidden utility lines or call the local utility company for assistance (contact with electric lines can lead to fire or electrical shock; damaging a gas line can result in an explosion; penetrating a water pipe will cause property damage or an electrical shock) Hold the power tool only by the insulated gripping surfaces when performing an operation where the accessory may contact hidden wiring or its own power cord (contact with a "live" wire will also make exposed metal parts of the power tool "live" and shock the operator) Do not work materials containing asbestos (asbestos is considered carcinogenic) Take protective measures when during work dust can develop that is harmful to one's health, combustible or explosive (some dusts are considered carcinogenic); wear a dust mask and work with dust/ chip extraction when connectable If the cord is damaged or cut through while working, do not touch the cord, but immediately disconnect the plug Never use tool when cord is damaged; have it replaced by a qualified person Always check that the supply voltage is the same as the voltage indicated on the nameplate of the tool (tools with a rating of 230V or 240V can also be connected to a 220V supply) If the drill bit becomes unexpectedly jammed (causing a sudden, dangerous reaction), immediately switch off the tool Be aware of the forces that occur as a result of jamming (especially when drilling metals); always use auxiliary handle F 2 and take a secure stance Always disconnect plug from power source before making any adjustment or changing any accessory WHEN CONNECTING NEW 3-PIN PLUG (U. K. ONLY): Do not connect the blue (= neutral) or brown (= live) wire in the cord of this tool to the earth terminal of the plug If for any reason the old plug is cut off the cord of this tool, it must be disposed of safely and not left unattended USE On/off 4 Switch locking for continuous use 5 Speed control for smooth starting 6 Maximum speed control With wheel C 7 the maximum speed can be adjusted from low to high - switch on the tool - lock the switch - turn wheel C to select maximum speed Changing direction of rotation 7 - when not properly set in left/right position, switch A cannot be activated !change direction of rotation only when tool is at a complete standstill 11 Normal drilling/screwdriving versus hammer drilling 8 !select drilling function only when tool is switched off Changing bits 9 - insert the bit as deep as possible in the chuck !do not use bits with a damaged shank Adjusting drilling depth 0 Holding and guiding the tool !- always use auxiliary handle F 2 (can be adjusted as illustrated) - keep ventilation slots H 2 uncovered - do not apply too much pressure on the tool; let the tool do the work for you Dust filter system @ For optimal dust suction performance !always ensure that filter J is located in dust box K before use - only use the dust filter system when drilling in concrete, brick and stone !do not use the dust filter system when drilling in wood, metal and plastic - only use drill bits for stone with a maximum diameter of 8 mm and a maximum length of 200 mm - clean filter J and dust box K frequently Removing dust filter system # !always close tube holder L when dust filter system is not being used Mounting dust filter system $ Use of dust filter system - the dust filter system with its telescopic action can be used in both horizontal and vertical working positions - dust box K @ keeps hanging down straight in all side handle positions - ensure that the dust filter system firmly rests against the wall/floor/ceiling (which also ensures drilling at a straight 90 angle) % !always pull switch A 2 to the maximum + select position 5 with wheel C 2 when using the dust filter system - remove drill bit from hole while tool is running to ensure dust suction performance - when dust filter system is not mounted, tool can be used again for drilling wood, metal and plastic Left- and right-hand use of side handle/dust filter system ^ Cleaning filter and dust box & In case of reduced dust suction performance, or when the collected dust has reached "MAX"-level M, filter J and dust box K should be cleaned - remove dust box K from dust filter system by pressing two red tabs N and slightly turning dust box towards you - remove filter J from dust box K and knock dust off of filter !do not wash filter with soap and water - empty dust box K - put back filter J in dust box K until it snaplocks - slide dust box K onto dust filter system until it snaplocks - mount spare filter bag as illustrated, when necessary * APPLICATION ADVICE Use the appropriate bits ( !NOISE/VIBRATION Measured in accordance with EN 60 745 the sound pressure level of this tool is 94 dB(A) and the sound power level 105 dB(A) (standard deviation: 3 dB), and the vibration m/s2 (hand-arm method). Technical file at: SKIL Europe BV (PT-SEU/PJE), 4825 BD Breda, NL. F CE DCLARATION DE CONFORMIT Nous dclarons sous notre propre responsabilit que ce produit est en conformit avec les normes ou documents normaliss suivants: EN 60 745, EN 55 014, conforme aux rglementations 73/23/CE, 2004/108/CE, 98/37/CE (jusqu'au 28. 12. 2009), 2006/42/CE ( partir du 29. 12. 2009). BRUIT/VIBRATION Mesur selon EN 60 745 le niveau de la pression sonore de cet outil est 94 dB(A) et le niveau de la puissance sonore 105 dB(A) (dviation standard: 3 dB), et la vibration m/s2 (mthode main-bras). Dossier technique auprs de: SKIL Europe BV (PT-SEU/PJE), 4825 BD Breda, NL. D CE KONFORMITTSERKLRUNG Wir erklren in alleiniger Verantwortung, da dieses Produkt mit den folgenden Normen oder normativen Dokumenten bereinstimmt: EN 60 745, EN 55 014, gem den Bestimmungen der Richtlinien 73/23/EG, 2004/108/EG, 98/37/EG (bis 28. 12. 2009), 2006/42/EG (ab 29. 12. 2009). GERUSCH/VIBRATION Gemessen gem EN 60 745 betrgt der Schalldruckpegel dieses Gertes 94 dB(A) und der Schalleistungspegel 105 dB(A) (Standard- abweichung: 3 dB), und die Vibration m/s2 (Hand-Arm Methode). Technische Unterlagen bei: SKIL Europe BV (PT-SEU/PJE), 4825 BD Breda, NL. NL CE CONFORMITEITSVERKLARING Wij verklaren, dat dit product voldoet aan de volgende normen of normatieve documenten: EN 60 745, EN 55 014, overeenkomstig de bepalingen van de richtlijnen 73/23/EG, 2004/108/EG, 98/37/EG (tot 28-12-2009), 2006/42/EG (vanaf 29-12-2009). GELUID/VIBRATIE Gemeten volgens EN 60 745 bedraagt het geluidsdrukniveau van deze machine 94 dB(A) en het geluidsvermogen-niveau 105 dB(A) (standaard deviatie: 3 dB), en de vibratie m/s2 (hand-arm methode). [. . . ] / EN 60 745 94 () i 105 () ( : 3 ), i /2 ( ). : SKIL Europe BV (PT-SEU/PJE), 4825 BD Breda, NL. UA GR CE YMBATOT : EN 60 745, EN 55 014, 73/23/EK, 2004/108/EK, 98/37/EK ( 28. 12. 2009), 2006/42/EK ( 29. 12. 2009). Y / Y EN 60 745 94 dB(A) o 105 dB(A) ( : 3 dB), m/s2 ( / ). : SKIL Europe BV (PT-SEU/PJE), 4825 BD Breda, NL. 07 SKIL Europe BV A. [. . . ]