User manual SKIL 6480

[. . . ] ) ME77 GB F D NL S DK N FIN E P I H CZ TR INSTRUCTIONS INSTRUCTIONS HINWEISE INSTRUCTIES INSTRUKTIONER INSTRUKTION ANVISNING OHJEET INSTRUCCIONES INSTRUES ISTRUZIONI LERS POKYNY KILAVUZ page 9 page 11 Seite 14 bladz. 34 oldal 37 strana 40 sayfa 42 PL RU UA GR RO BG SK HR SCG SLO EST LV LT INSTRUKCJA O INSTRUCIUNI strona 45 48 51 54 pagina 57 YKA3A POKYNY UPUTE UPUTSTVA NAVODILA INSTRUKCIJA INSTRUKCIJA 60 strana 63 stranica 66 stranica 68 stran 70 lappuse 75 puslapis 78 KASUTUSJUHEND leheklg 73 www. skileurope. com SKIL Europe BV - Konijnenberg 60 4825 BD Breda - The Netherlands 03/06 2609001865 1 6480 950 W 2, 6 kg 0-800 RPM 0-2800 RPM 0-12800 p/min 0-44800 p/min 13 6485 950 W 2, 6 kg 0-800 RPM 0-2800 RPM 45mm 0-12800 p/min 0-44800 p/min 13 45mm 6480 6485 2 HF G HF G E J K D C B A E J K D C B A 2 3 4 5 3 6 12345 1-3 7 8 6 8 10 15 30 2+5 2+5 1+4 2+5 2+5 1+4/5 1+4/5 2+5 2+5 2+5 1+5 2+5 2+5 1+5 1+4/5 1+5/5 4 9 G 0 H 5 ! 6480 6485 1 3 2 @ 6 # $ HSS PHILLIPS POZIDRIV SLOTTED 7 % ^ & * ( ACCESSORIES 2610073400 In Deutschland nicht lieferbar 8 GB Hammer drill INTRODUCTION 6480/6485 This tool is intended for hammer drilling in brick, concrete and stone as well as for drilling in wood, metal, ceramic and plastic; tools with electronic speed control and left/right rotation are also suitable for screwdriving and thread cutting Read and save this instruction manual TECHNICAL SPECIFICATIONS 1 TOOL ELEMENTS 2 A B C D E F G H J K Switch for on/off and speed control Button for switch locking Wheel for maximum speed control Switch for changing direction of rotation Switch for selecting mechanical speed Switch for selecting drilling function Indicator of selected direction of rotation Indicator of selected drilling function Auxiliary handle Ventilation slots SAFETY GENERAL SAFETY INSTRUCTIONS WARNING!Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury. The term "power tool" in all of the warnings listed below refers to your mains operated (corded) power tool. [. . . ] This will ensure that the safety of the power tool is maintained. SAFETY INSTRUCTIONS FOR HAMMER DRILLS Always check that the supply voltage is the same as the voltage indicated on the nameplate of the tool (tools with a rating of 230V or 240V can also be connected to a 220V supply) If the drill bit becomes unexpectedly jammed (causing a sudden, dangerous reaction), immediately switch off the tool Be aware of the forces that occur as a result of jamming (especially when drilling metals); always use auxiliary handle and take a secure stance Always disconnect plug from power source before making any adjustment or changing any accessory WHEN CONNECTING NEW 3-PIN PLUG (U. K. ONLY): Do not connect the blue (= neutral) or brown (= live) wire in the cord of this tool to the earth terminal of the plug If for any reason the old plug is cut off the cord of this tool, it must be disposed of safely and not left unattended USE Wear ear protectors with hammer drills (exposure to noise can cause hearing loss) Use auxiliary handles supplied with the tool (loss of control can cause personal injury) Avoid damage that can be caused by screws, nails and other elements in your workpiece; remove them before you start working Always keep the cord away from moving parts of the tool When you put away the tool, switch off the motor and ensure that all moving parts have come to a complete standstill Use completely unrolled and safe extension cords with a capacity of 16 Amps (UK 13 Amps) In case of electrical or mechanical malfunction, immediately switch off the tool and disconnect the plug SKIL can assure flawless functioning of the tool only when original accessories are used Use only accessories with an allowable speed matching at least the highest no-load speed of the tool This tool should not be used by people under the age of 16 years Do not work materials containing asbestos (asbestos is considered carcinogenic) Take protective measures when during work dust can develop that is harmful to one's health, combustible or explosive (some dusts are considered carcinogenic); wear a dust mask and work with dust/chip extraction when connectable Be careful not to drill or drive into areas where electrical wires may be contacted; always use auxiliary handle The noise level when working can exceed 85 dB(A); wear ear protection If the cord is damaged or cut through while working, do not touch the cord, but immediately disconnect the plug Never use tool when cord is damaged; have it replaced by a qualified person On/Off 3 Switch locking for continuous use 4 Speed control for smooth starting 5 Maximum speed control 6 With wheel C the maximum speed can be adjusted from low to high (1-5) - switch on the tool - lock the switch - turn wheel C to select maximum speed 2 Mechanical speeds 7 !change speed only when tool is switched off 1 = LOW SPEED - high torque - for screwdriving and drilling large diameters - for tapping thread 2 = HIGH SPEED - lower torque - for drilling small diameters For determining the optimal speed table 8 can be used as reference Changing direction of rotation 9 - when not properly set in left/right position, switch A cannot be activated - indicator G shows the selected direction of rotation !change direction of rotation only when tool is at a complete standstill Normal drilling/screwdriving versus hammer drilling 0 - indicator H shows the selected drilling function !select drilling function only when tool is switched off Changing bits !- insert the bit as deep as possible in the chuck !do not use bits with a damaged shank Adjusting drilling depth @ Holding and guiding the tool # !always use auxiliary handle (can be adjusted as illustrated) - keep the ventilation slots uncovered - do not apply too much pressure on the tool; let the tool do the work for you 10 APPLICATION ADVICE ELEMENTS DE L'OUTIL 2 A Interrupteur pour mise en marche/arrt et rglage de la vitesse B Bouton de blocage de l'interrupteur C Molette de rglage de la vitesse maximum D Commutateur pour inverser le sens de rotation E Commutateur pour slectionner la vitesse mcanique F Commutateur pour slectionner la fonction de perage G Indicateur du sens de rotation slectionn H Indicateur de la fonction de perage slectionne J Poigne auxiliaire K Arations Use the appropriate bits $ !only use sharp bits For drilling in concrete or stone a steady pressure on the drill is required When drilling ferrous metals - pre-drill a smaller hole, when a large hole is required - lubricate drill bit occasionally with oil When turning in a screw at/near the cross cut end or an edge of wood, pre-drill a hole in order to avoid cracking of the wood Splinterfree drilling in wood % Dustfree drilling in walls ^ Dustfree drilling in ceilings & Drilling in tiles without skidding * For more tips see www. skileurope. com SECURITE INSTRUCTIONS GENERALES DE SECURITE ATTENTION!Le nonrespect des instructions indiques ci-aprs peut entraner un choc lectrique, un incendie et/ou de graves blessures sur les personnes. La notion d'outil lectroportatif mentionne par la suite se rapporte des outils lectriques raccords au secteur (avec cble de raccordement). 1) PLACE DE TRAVAIL a) Maintenez l'endroit de travail propre et bien clair. Un lieu de travail en dsordre ou mal clair augmente le risque d'accidents. b) N'utilisez pas l'appareil dans un environnement prsentant des risques d'explosion et o se trouvent des liquides, des gaz ou poussires inflammables. Les outils lectroportatifs gnrent des tincelles risquant d'enflammer les poussires ou les vapeurs. c) Tenez les enfants et autres personnes loigns durant l'utilisation de l'outil lectroportatif. En cas d'inattention vous risquez de perdre le contrle sur l'appareil. 2) SECURITE RELATIVE AU SYSTEME ELECTRIQUE a) La fiche de secteur de l'outil lectroportatif doit tre approprie la prise de courant. NOISE/VIBRATION Measured in accordance with EN 60 745 the sound pressure level of this tool is 104 dB(A) and the sound power level 115 dB(A) (standard deviation: 3 dB), and the vibration 15. 8 m/s2 (hand-arm method). CE DCLARATION DE CONFORMIT Nous dclarons sous notre propre responsabilit que ce produit est en conformit avec les normes ou documents normaliss suivants: EN 60 745, EN 55 014, conforme aux rglementations 73/23/EC, 89/336/EC, 98/37/EC. BRUIT/VIBRATION Mesur selon EN 60 745 le niveau de la pression sonore de cet outil est 104 dB(A) et le niveau de la puissance sonore 115 dB(A) (dviation standard: 3 dB), et la vibration 15, 8 m/s2 (mthode main-bras). [. . . ] , : EN 60 745, EN 55 014, 73/23/EC, 89/336/EC, 98/37/EC. / co o EN 60 745 104 (A) e - 115 (A) ( : 3 dB), - 15, 8 /2 ( ). CE , : EN 60 745, EN 55 014, 73/23/, 89/336/, 98/37/. / EN 60 745 104 () i 115 () ( : 3 ), i 15, 8 /2 ( ). [. . . ]