User manual SKIL 9445

[. . . ] ANGLE GRINDER 9445 (F0159445. . ) GB F D NL S DK N FIN E P I H CZ TR PL ORIGINAL INSTRUCTIONS . 95 INSTRUCIUNI DE FOLOSIRE ORIGINALE . 68 OR<J<NAL <fiLETME TAL<MATI . 143 www. skileurope. com www. skilmasters. com SKIL Europe BV - Konijnenberg 60 4825 BD Breda - The Netherlands 02/09 ME77 2610398193 1 9445 900 EPTA 01/2003 Watt 2, 4 kg 11500/min RUBBER 125 mm 22 mm M14 2 J K M E D L A G F H H B B C 2 3 4 5 6 7 G L 3 8 9 4 0 ! @ # ACCESSORIES SKIL nr. 125 mm 2610399439 5 GB Angle grinder INTRODUCTION 9445 This tool is intended for grinding, cutting and deburring metal and stone materials without the use of water; with the appropriate accessories the tool can also be used for brushing and sanding Cutting operations with bonded abrasive cut-off wheels are only allowed when a cut-off guard (available as optional SKIL accessory 2610399439) is used Read and save this instruction manual 3 TECHNICAL SPECIFICATIONS 1 TOOL ELEMENTS 2 A B C D E F G H J K L M Spindle Clamping flange Accessory key Spindle-lock button Unlocking button Auxiliary handle Protective guard Mounting flange On/off locking switch Second on/off locking switch Protective guard screw Ventilation slots SAFETY GENERAL SAFETY INSTRUCTIONS WARNING! [. . . ] d) Use special care when working corners, sharp edges etc. c) When the wheel is binding or when interrupting a cut for any reason, switch off the power tool and hold the power tool motionless until the wheel comes to a complete stop. Never attempt to remove the cutoff wheel from the cut while the wheel is in motion, otherwise kickback may occur. Investigate and take corrective action to eliminate the cause of wheel binding. d) Do not restart the cutting operation in the workpiece. Let the wheel reach full speed and carefully re-enter the cut. The wheel may bind, walk up or kickback if the power tool is restarted in the workpiece. e) Support panels or any oversized workpiece to minimize the risk of wheel pinching and kickback. Large workpieces tend to sag under their own weight. Supports must be placed under the workpiece near the line of cut and near the edge of the workpiece on both sides of the wheel. f) Use extra caution when making a "pocket cut" into existing walls or other blind areas. The protruding wheel may cut gas or water pipes, electrical wiring or objects that can cause kickback. 5) SAFETY WARNINGS SPECIFIC FOR SANDING OPERATIONS a) When sanding, do not use excessively oversized sanding disc paper. Follow the manufacturers' recommendations when selecting sanding paper. Larger sanding paper extending beyond the sanding pad presents a laceration hazard and may cause snagging, tearing of the disc, or kickback. 6) SAFETY WARNINGS SPECIFIC FOR WIRE BRUSHING OPERATIONS a) Be aware that wire bristles are thrown by the brush even during ordinary operation. Do not overstress the wires by applying excessive load to the brush. The wire bristles can easily penetrate light clothing and/ or skin. b) If the use of a guard is recommended for wire brushing, do not allow any interference of the wire wheel or brush with the guard. Wire wheel or brush may expand in diameter due to work load and centrifugal forces. GENERAL Only use this tool for dry grinding/cutting Only use the flanges which are supplied with this tool This tool should not be used by people under the age of 16 years 8 Always disconnect plug from power source before making any adjustment or changing any accessory ACCESSORIES SKIL can assure flawless functioning of the tool only when the correct accessories are used which can be obtained from your SKIL dealer For mounting/using non-SKIL accessories observe the instructions of the manufacturer concerned Never use reducors or adaptors to fit large-hole grinding/cutting discs Never use accessories with a "blind" threaded hole smaller than M14 x 21 mm OUTDOOR USE Connect the tool via a fault current (FI) circuit breaker with a triggering current of 30 mA maximum BEFORE USE Before using the tool for the first time, it is recommended to receive practical information Do not work materials containing asbestos (asbestos is considered carcinogenic) Use suitable detectors to find hidden utility lines or call the local utility company for assistance (contact with electric lines can lead to fire or electrical shock; damaging a gas line can result in an explosion; penetrating a water pipe will cause property damage or an electrical shock) Dust from material such as paint containing lead, some wood species, minerals and metal may be harmful (contact with or inhalation of the dust may cause allergic reactions and/or respiratory diseases to the operator or bystanders); wear a dust mask and work with a dust extraction device when connectable Certain kinds of dust are classified as carcinogenic (such as oak and beech dust) especially in conjunction with additives for wood conditioning; wear a dust mask and work with a dust extraction device when connectable Follow the dust-related national requirements for the materials you want to work with Be careful when cutting grooves, especially in supporting walls (slots in supporting walls are subject to country-specific regulations; these regulations are to be observed under all circumstances) Clamp the workpiece in case it does not remain stationary from its own weight Do not clamp the tool in a vice Use completely unrolled and safe extension cords with a capacity of 16 Amps (U. K. 13 Amps) DURING USE Inrush currents cause short-time voltage drops; under unfavourable power supply conditions, other equipment may be affected (if the system impedance of the power supply is lower than 0, 104 + j0, 065 Ohm, disturbances are unlikely to occur); if you need further clarification, you may contact your local power supply authority If the cord is damaged or cut through while working, do not touch the cord, but immediately disconnect the plug; never use the tool with a damaged cord In case of electrical or mechanical malfunction, immediately switch off the tool and disconnect the plug In case of current interruption or when the plug is accidentally pulled out, unlock the on/off switch J 2 immediately in order to prevent uncontrolled restarting AFTER USE After switching off the tool, never stop the rotation of the accessory by a lateral force applied against it WHEN CONNECTING NEW 3-PIN PLUG (U. K. [. . . ] Des autres applications (comme trononner ou travailler avec brosses mtalliques) peuvent entraner des valeurs de vibration diffrentes Beim Oberflchenschleifen Beim Schleifen Unsicherheit (K) !Trennen oder Brsten) knnen andere Vibrationswerte aufweisen Tijdens het slijpen Tijdens het schuren Onzekerheid (K) !Andere toepassingen (zoals doorslijpen of werken met draadborstels) kunnen andere vibratie-waarden opleveren Ved smrgling ytor Ved slipning Onoggrannhet (K) !Andra applikationer (ssom kapning eller borstning) dr kan vibrationsvrdena Ved overfladeslibning Ved pudsning Usikkerhed (K) ! [. . . ]