User manual SKIL FOX 3 EN 1

[. . . ] COM Multi sander INTRODUCTION 7220/7226 c) d) ? This tool is intended for dry sanding and finishing of wood, painted surfaces, plastic and filler ? This tool is not intended for professional use ? Read and save this instruction manual ? TECHNICAL SPECIFICATIONS ?Backing pad for random orbit sanding C ?Flexible sanding attachment* Finger attachment* K ?Knob for mounting sanding attachments* M ? [. . . ] unplug tool before removing/mounting backing pads !Pad screw D becomes hot during use; do not touch it before it has cooled down ? Mounting of sanding sheet ? disconnect the plug -- mount VELCRO sanding sheet as illustrated !The dust suction requires the use of perforated sanding sheets !Perforation in sanding sheet should correspond with perforation in sanding foot !Always use the tool with the total sanding surface covered with sanding paper ? Two-speed switch ?-- switch on/off the tool by pushing switch F ?forward/ backwards (3 positions) 0 = off 1 = low speed 2 = high speed SAFETY INSTRUCTIONS FOR SANDERS ? Avoid damage that can be caused by screws, nails and other elements in your workpiece; remove them before you start working ? Always keep the cord away from moving parts of the tool; direct the cord to the rear, away from the tool ? Secure the workpiece (a workpiece clamped with clamping devices or in a vice is held more securely than by hand) ? When you put away the tool, switch off the motor and ensure that all moving parts have come to a complete standstill ? Use completely unrolled and safe extension cords with a capacity of 16 Amps (U. 13 Amps) ? In case of electrical or mechanical malfunction, immediately switch off the tool and disconnect the plug ? SKIL can assure flawless functioning of the tool only when original accessories are used ? This tool should not be used by people under the age of 16 years ? The noise level when working can exceed 85 dB(A); wear ear protection ? If the cord is damaged or cut through while working, do not touch the cord, but immediately disconnect the plug ? Never use the tool when cord is damaged; have it replaced by a qualified person ? Always check that the supply voltage is the same as the voltage indicated on the nameplate of the tool (tools with a rating of 230V or 240V can also be connected to a 220V supply) ? This tool is not suitable for wet sanding ? Do not work materials containing asbestos (asbestos is considered carcinogenic) ? Dust from material such as paint containing lead, some 7 USE -- select position 1 for accurate sanding (when working with delta-tip G or special sanding attachments H, J or K) -- select position 2 for fast sanding !Before the sanding surface reaches the workpiece, you should switch on the tool !Before switching off the tool, you should lift it from the workpiece ? Mounting special sanding attachments (not standard included) ?-- mount base plate C (similar to mounting backing pads) -- mount attachment H, J or K onto base plate C and fasten it by turning knob L clockwise -- mount corresponding VELCRO sanding sheet to sanding attachment -- remove attachments or change their position by turning knob L counter-clockwise -- 5 sanding positions ? Dust suction ?-- empty dustbox M regularly for optimal dust pick-up performance For using vacuum cleaner -- remove dustbox M by pressing knob N and hold it in that position while pulling dustbox backwards -- connect vacuum cleaner to extension P !Do not use dustbox/vacuum cleaner when sanding metal ? Holding and guiding the tool ?-- guide the tool parallel to the working surface !Do not apply too much pressure on the tool; let the sanding surface do the work for you -- do not tilt the tool in order to avoid unwanted sanding marks !While working, always hold the tool at the greycoloured grip area(s) -- keep ventilation slots Q ?uncovered ? Use different grit sizes when the working surface is rough: -- start sanding with coarse or medium grit -- finish with fine grit ? For more tips see www. Com MAINTENANCE / SERVICE ? This tool is not intended for professional use ? Always keep tool and cord clean (especially ventilation slots Q ?) -- remove adhering sanding dust with a brush !Disconnect the plug before cleaning ? If the tool should fail despite the care taken in manufacturing and testing procedures, repair should be carried out by an after-sales service centre for SKIL power tools -- send the tool undismantled together with proof of purchase to your dealer or the nearest SKIL service station (addresses as well as the service diagram of the tool are listed on www. Com) ENVIRONMENT ? Do not dispose of electric tools, accessories and packaging together with household waste material (only for EU countries) -- in observance of European Directive 2012/19/EC on waste of electric and electronic equipment and its implementation in accordance with national law, electric tools that have reached the end of their life must be collected separately and returned to an environmentally compatible recycling facility -- symbol ?SKERHETSANVISNINGAR FR SLIPMASKINER ? Undvik skador genom att ta bort skruvar, spikar eller andra freml ur arbetsstycket; ta dem bort innan du startar ett arbete ? Hll alltid sladden p skert avstnd frn rrliga maskindelar; fr sladden bakt bort frn maskinen ? Stt fast arbetsstycket (ett arbetsstycke fastsatt med skruvtvingar eller i ett skruvstd r mera stabilt n om det hlls fast fr hand) ? Nr du stller ifrn dig maskinen mste motorn vara frnslagen och de rrliga delarna ska ha stannat fullstndigt ? Anvnd helt utrullade och skra frlngningssladdar med kapacitet p 16 A ? I hndelse av onormala elektriska eller mekaniska strningar, stng genast av maskinen och dra ur stickkontakten ? SKIL kan endast garantera att maskinen fungerar felfritt om originaltillbehr anvnds ? Den hr maskinen ska inte anvndas av personer under 16 r ? Ljudnivn vid arbete kan verskrida 85 dB(A); anvnd hrselskydd ? Skadas eller kapas ntsladden under arbetet, rr inte vid sladden utan dra genast ut stickkontakten ? Anvnd ej maskinen om sladden r trasig; lt den byta ut av en kvalificerad person ? Kontrollera alltid att den tillfrda strmtypen stmmer med spnningen som anges p maskinens mrkplt (maskiner med beteckningen 230V eller 240V kan ven anslutas till 220V) ? Denna maskin r inte lmplig till vattenslipning ? Asbesthaltigt material fr inte bearbetas (asbest anses vara cancerframkallande) ? Viss typ av damm, exempelvis frg som innehller bly, vissa trsorter, mineraler och metaller kan vara hlsovdliga om de inhaleras (hudkontakt eller inhalering kan ge allergisk reaktion och/eller luftvgsproblem/sjukdom hos personer i nrheten); anvnd andningsskydd och arbeta med en dammuppsamlare om sdan anslutning finns ? Vissa typer av damm r klassificerade s som carcinogeniska (t. [. . . ] ?i/sau de a introduce acumulatorul n scula electric?, de a o ridica sau de a o transporta, asigura?i v?Nu permite?i persoanelor care nu sunt familiarizate cu ma?ina sau care n-au citit prezentele instruc?iuni, s?PENTRU ?LEFUITOARE ? Evita?i daunele provocate de ?uruburi, ?inte ?i alte elemente din timpul lucrului; nl?tura?i aceste elemente nainte de a trece la ac?iune ? Feri?i ntotdeauna cordonul de p?rtile n mi?care ale sculei; orientati cordonul spre spate, la distan??dect manual) ? Cnd pune?i instrumentul la o parte, deconecta?i motorul ?i asigura?i-v? [. . . ]