User manual SLAUTTERBACK SS10G MARK II PRODUCT MANUAL

[. . . ] ® Super Squirt SS10G Mark II Product Manual Manual Number: 19600-133 Revision: C ® Super Squirt SS10G Mark II Product Manual Manual Number: 19600-133 Revision: C Date: 11/07/00 Copyright 2000 Slautterback Corporation ! WARNING To avoid personal injury and damage to equipment and property, read the product manual completely before installing, operating or servicing this equipment. Follow all safety warnings located on this product and in the product manual. Consult the safety precautions section of the product manual for an explanation of all safety symbols used on this equipment. Retain the product manual for the life of this product. [. . . ] Refer to Temperature Check in Maintenance section of the handgun manual. 2. 3. 4. 5. 2 1 © Copyright 2000 Slautterback Corporation Super Squirt SS10G Mark II 19600-133 Rev. C 11/07/00 2000008a 13 5. 3. 3 Adhesive Flow Adjustment ! CAUTION: For maximum performance and motor life, do not allow pump motor to stall. A prolonged stall condition will cause motor to go into thermal overload. Flow Control Valve An adjustable pressure regulating device is mounted on the pump under the melt unit chassis. Adjust adhesive flow with flow control knob [1] on right side of melt unit. To increase pressure and adhesive flow, turn knob [1] clockwise. To decrease pressure and adhesive flow, turn knob [1] counterclockwise. To achieve minimum pressure and lowest flow rate suitable for application, turn knob fully counterclockwise. Gradually turn clockwise until desired pressure and flow rate is reached. ® 1 2000359 14 Super Squirt SS10G Mark II 19600-133 Rev. C 11/07/00 Copyright 2000 Slautterback Corporation 6 Maintenance ! WARNING: Hot Melt materials can cause severe burns resulting in disfigurement or blindness. Follow these precautions before beginning any maintenance: · Wear protective clothing, safety goggles, and safety gloves. · Turn pump motor switch to off position. Depressurize applicator(s) by triggering. · Unless stated otherwise, always allow melt unit to cool before beginning any maintenance. · Disconnect hose electrical connector when hose fittings are disconnected and power is off. CAUTION: To prevent damage to components (hose fittings, etc. ), heat part(s) being serviced to approximately 121 °C (250°F) prior to dismantling, assembling, or adjusting. Heat parts by applying power to the unit using a hand held hot air gun or placing parts on a hot plate. Failure to do this will result in stripped threads and ruining both parts and tools. CAUTION: To avoid arcing of electrical contacts and possible failure of components, do not connect electrical connectors when the hose power switch is on. ! ! © Copyright 2000 Slautterback Corporation Super Squirt SS10G Mark II 19600-133 Rev. C 11/07/00 15 6. 1 Preventive Maintenance 6. 1. 1 Monthly Inspection Procedure 1. Verify hose is properly supported so it is not over stressed during use. Minimum bend radius is 20. 32 cm (8 in. ) when hot. [. . . ] C 11/07/00 Copyright 2000 Slautterback Corporation Item Heated Supply Hoses Description (Quantity) Hose, L2, capillary, 2. 44 m (8 ft), 232 °C (450 °F), 115 VAC Hose, L2, capillary, 3. 66 m (12 ft), 232 °C (450 °F), 115 VAC L2 standard handgun spare, 115 VAC Kit, L2 heater, 115 VAC Kit, microswitch for L2 handgun L2 standard handgun spare, 115 VAC Constant tension balancer, 1­4 Ib Constant tension balancer, 2­5 Ib Hose hammock Swivel subassembly Needle packing washer Teflon needle seal Fiber washers Teflon seat plate Screw, seat plate Part Number 26269 08-N 26269-12-N 75085-000 79075-1 79095 75085-000 11030 11031 30087 73161 16528-18 16528-17 16528-25 16528-22 16528-23 © Copyright 2000 Slautterback Corporation Super Squirt SS10G Mark II 19600-133 Rev. C 11/07/00 33 This page intentionally left blank. 34 Super Squirt SS10G Mark II 19600-133 Rev. C 11/07/00 Copyright 2000 Slautterback Corporation ® PRODUCT MANUAL FEEDBACK FORM Fax it to us at (831) 658-6096 Please help us improve our manual. Send this form with any suggestions you may have. [. . . ]