User manual SMC 2622W-P

[. . . ] EZ ConnectTM Wireless Print Server User Guide SMC2622W-P SMC2622W-U Table of Contents Chapter 1 Introduction: page 3 Features Package Contents Models LED indicators Diagnostic Push Button LAN Installation: page 8 Print Server Configuration: page 10 Overview Using the Windows Wizard Alternatives to the Windows Wizard Wireless Configuration Advanced Configuration and Management Client PC Configuration: page 18 Overview Windows Peer-to-Peer Print Driver Windows SMB Printing Windows with Server-based Print Queues Macintosh (AppleTalk) BiAdmin Management Utility: page 29 Requirements Installation Operation Web Interface Setup: page 37 Overview Preparation Connecting to the Print Server Configuration Screens Special Features: page 47 Overview Internet Printing Protocol (IPP) Internet Mail Printing SNMP Chapter 2 Chapter 3 English 1 Chapter 4 Chapter 5 Chapter 6 Chapter 7 Chapter 8 Troubleshooting: page 62 Overview Hardware & LAN Problems AppleTalk (Macintosh) Windows Printing Problems Specifications: page 71 General Specifications Regulatory Approvals Safety Instructions Wireless PCMCIA Adapter Installation: page 74 Network Server Configuration: page 77 Windows NT Server Windows 2000 Server Unix Systems Contact SMC & Warranty Information Appendix A Appendix B Appendix C English 2 Chapter 1: Introduction Features Congratulations on the purchase of your new Print Server. This device was designed to provide a simple and efficient network printing solution. It is packed with features, including: · Versatility. The Print Server supports TCP/IP, SMB (Service Message Block), AppleTalk (EtherTalk), and NetBEUI. [. . . ] Otherwise, it will not be able to decrypt the data. Default Key Select the key you wish to be the default. Transmitted data is ALWAYS encrypted using the Default Key; the other Keys are for decryption only. Key Table: This table is used when Encrypting and Decrypting data. All stations, including this Access Point, always transmit data encrypted using their default key. The key number (1, 2, 3, 4) is also transmitted. The receiving station will use the key number (1, 2, 3, 4) to determine which key value to use for decryption. If the key value does not match the transmitting station, decryption will fail. The easiest way to ensure there are no problems is to have every Station, including the Access Point, use the same key table (all entries identical). Then, it does not matter which key is used as the default key. If selected, data is encrypted using the key before being transmitted. The receiving station must be set to use 128 Bit Encryption, and have the same Key value. Otherwise, it will not be able to decrypt the data. Key Enter the key value you wish to use. Other stations must have the same key Options are "Open System" or "Shared Key". Some Wireless cards do not support both methods. Check your Wireless card's documentation to determine the correct value. Ensure that all Wireless stations use the same setting as the Access Point. English 128 Bit Encryption WEP Authentication 45 Other Screens Server Status This screen shows server system data and the current settings for all of the other screens. It is read-only; no data can be input on this screen. Printer Status This screen displays the current status of each port. For each port, the following data is listed: · Connected Printer - the model name of the printer connected to the port, if the printer name is known. (If the printer is not bidirectional, this information is unavailable. ) · Status - the current status of the printer (On-line, Off-line, Out of paper) · Printing Information - this will show either Idle or Printing. [. . . ] Any replaced or repaired product carries, either a 30-day limited warranty or the remainder of the initial warranty, whichever is longer. SMC is not responsible for any custom software or firmware, configuration information, or memory data of Customer contained in, stored on, or integrated with any products returned to SMC pursuant to any warranty. Products returned to SMC should have any customer-installed accessory or add-on components, such as expansion modules, removed prior to returning the product for replacement. SMC is not responsible for these items if they are returned with the product. [. . . ]