User manual SMC 7003-USB

[. . . ] EZ Connect ADSL USB Modem ADSL USB Modem N N N N N N High-speed Internet access over existing phone lines One RJ-11 ADSL port Delivers USB plug-and-play installation Supports full-rate DMT connection (8 Mbps downstream, 1 Mbps upstream) Supports econmical G. lite connection (1. 5 Mbps downstream, 512 Kbps upstream) Graphic interface for ADSL connection management User Guide SMC7003-USB EZ Connect ADSL USB Modem User Guide From SMC's EZ Connect line of feature-rich SOHO solutions 6 Hughes Irvine, CA 92618 Phone: (949) 707-2400 April 2001 Pub. # 150552-102 R02 Information furnished by SMC Networks, Inc. (SMC) is believed to be accurate and reliable. However, no responsibility is assumed by SMC for its use, nor for any infringements of patents or other rights of third parties which may result from its use. [. . . ] This driver supports PPP (RFC 2364) with PVC or SVC connections. The device drivers are summarized in the table below: Driver Type WAN* Protocols RFC 2364 Windows OS Windows 98 Windows 98 SE Windows 2000 LAN RFC 1483 Windows 98 Windows 98 SE Windows 2000 ATM* RFC1577 RFC 2364 Windows 98 SE Windows 2000 * Windows Dial-up Networking and Dial-up ATM Support should be installed in your operating system prior to installing these drivers. 3-3 DRIVER INSTALLATION Prerequisite Information The following information may be required, depending on the driver you install. Contact your DSL service provider before proceeding with software installation. · IP Address Settings - the software installation process allows the server to dynamically assign IP Address settings. If your application requires a static setting for specific address information you will need to know the following: IP Address Subnet Mask (for Bridged Ethernet applications only) Default Gateway (for Bridged Ethernet applications only) · Name Server Information - the modem software installation process allows the server to dynamically assign Name Server Address settings. If your application requires a static setting for specific address information you will need to know the following: Primary DNS Address Secondary DNS Address Primary WINS Address Secondary WINS Address · · · · · · · Mode (for LAN applications only) Virtual Path ID (VPI)* Virtual Circuit ID (VCI)* Encapsulation type* Modulation type* User Name (for PPP applications only) Password (for PPP applications only) 3-4 DRIVER INSTALLATION * These items are only required if you are not using default values. 3-5 DRIVER INSTALLATION Running the Setup Program Note: Please view the README. TXT file on the CD for product related information. Start up your PC with the modem disconnected. After Windows starts, insert the CD-ROM that comes with the EZ Connect ADSL USB Modem in your CD drive, and click Setup. exe to start the installation procedure. The "Welcome" window provides an opportunity to quit the setup process to exit all Windows programs before continuing. If the Windows programs were previously closed, click Next. The "Start Copying Files" window displays the default driver settings. To automatically select the default settings, click Next and continue to Step 7. To change the driver settings, click Customize and continue to step 5. 3-6 DRIVER INSTALLATION 5. Then specify the VPI (Virtual Path), VCI (Virtual Channel), Layer 3 Encapsulation type, and Modulation type, and click Next. Check with your service provider for the correct settings. 6. The "Start Copying Files" window will be redisplayed. You may review the current settings and click Customize or Back to change the settings. Click Next to accept the current settings; a message will be displayed indicating that files are being copied. The "Setup Complete" window indicates successful completion of the installation process. Select the Yes, I want to restart my computer now option, remove any disks from their drives, and click Finish. Continue with the Modem Installation section. 3-7 DRIVER INSTALLATION Installing the Modem Note: For Windows 98 SE applications, you may need the Windows 98 SE source files to complete the installation. Microsoft Windows has an auto-detect feature, known as "Plug and Play, " that is capable of identifying when new hardware has been installed. After you run the setup program, reboot your PC, and then connect the EZ Connect ADSL USB Modem to your PC. [. . . ] From your PC desktop click Start - Programs - SMC DSL Modem - Uninstall. A notification message will appear indicating that the setup process has begun. Click Remove in the "DSL Modem Installer" window. A message will be displayed asking you to confirm removal of the USB ADSL modem software, click Yes. [. . . ]