User manual SMC 7824M/VSW

[. . . ] Installation Manual TigerAccessTM EE IMN Information furnished by SMC Networks, Inc. (SMC) is believed to be accurate and reliable. However, no responsibility is assumed by SMC for its use, nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of SMC. [. . . ] NOTE ­ Module is not used in the first release. It means that this switch provides 24 subscriber interfaces for VDSL lines supporting the data rate of up to 100 Mbps both in upstream and downstream direction, and also provides up to 4 uplink interfaces (both optical and electrical type) for the connection to the IP network with consolidating the traffic from subscribers. The voice bandwidth can still be separated from the data traffic using the internal splitter for POTS. The switch is designed to be used in indoor racks only and installed either in ETSI or 19" racks. This document basically describes installation with the switch in a 19" rack, but deploying the system in an ETSI rack is not so different. But this switch cannot be installed in an ETSI rack with 300mm depth. For more information about deploying the system in your rack, refer to your rack configuration plan. Fig. 2. 1 Product View 12 SMC7824M/VSW Installation Manual TigerAccessTM EE IMN The interfaces of the switch are to find in Fig. 2. 1. GTX Uplink Ports LEDs of VDSL i/f Console Access MGMT Optional Expansion Slots VDSL/POTS (1-24) System LED Fig. 2. 2 Front Interfaces of the switch Name Uplink i/f Function GTX uplink fixed type: Connection to the IP network with electrical type interfaces Optional Expansion slot: Blank slot for optional uplink module RJ45 Connector Type SFP (1000Base-X) SC, SFF package (GE-PON) · · VDSL POTS CONSOLE 2-port 1000Base-X 1-port GE-PON + 1-port 1000Base-X RJ21 RJ21 RJ45 (RS232) Connection to the VDSL subscribers Connection to the PBX or PSTN CLI access to configure the functions for system operation MGMT Outband TMN-OS Interface RJ45 Tab. 2. 1 Front Access Interfaces of the switch 2. 1 2. 1. 1 Product Specification System The switch supports the following system features: · · · · · Non-blocking wire speed performance switching fabric (12. 8 Gbps) 24-port VDSL2 interfaces Integrated splitters for narrowband services 2-port fixed 10/100/1000Base-T Gigabit Ethernet uplink interfaces 1-slot for uplink interface (modular type) - 2-port 1000Base-X SFP type module - 1-port GE-PON SFF (10km or 20km) + 1-port 1000Base-X SFP type module LED indicator Fixed fans for internal cooling · · SMC7824M/VSW 13 IMN Installation Manual TigerAccessTM EE 2. 1. 2 Functionalities The switch provides the following functionalities: Advanced VDSL2 Function · · · · · · · · Configuration of xDSL line rate Provision of different band plans and profiles for xDSL interfaces VDSL2 interface according to ITU-T G. 993. 2 Band plans 997, 998 and profiles 8a, 8b, 12a, 12b and 17a configurable per port Support of 30a profile according VDSL2 standard Number of band-plans and PSD shape fully programmable Support of Impulse Noise Protection Voice and data communication can be shared on the existing telephone wire simultaneously Layer 2 · · · · · · · · · · · · · · · · Standard Ethernet Bridging 16K MAC entries 4K active VLANs for 802. 1q tagged frame VLAN stacking/translation Spanning tree protocols Jumbo frame 9K Link Aggregation (LAG) on uplink I/F 802. 1x port/MAC based authentication Port/protocol based VLAN association Private VLAN (port isolation) VLAN Stacking (QinQ) Service multiplexing based on VLANs Loop detection DHCP Server DHCP relay agent (incl. Option 82) Simplified DHCP relay agent Multicast · · · IGMPv1/v2/v3 256 L2 multicast groups IGMP snooping for IP multicasting QoS · · · · · Traffic scheduling (SP, DWRR) Port rate limit with the ingress/egress shaping Conditional rate limiting Queue mapping according to ingress/egress port, MAC, 802. 1q, 802. 1p, ToS/DSCP, IP SA/DA, TCP/UDP Access control lists based on port, MAC address, Ether type, IP SA/DA, IP multicast address, TCP/UDP 14 SMC7824M/VSW Installation Manual TigerAccessTM EE IMN Security · · · · · · 802. 1x MAC/port based authentication Storm control for broadcast, multicast and unknown unicast packets DoS protection Outband management IP source guard Secure Shell (SSH) Management · · · · · Serial/Telnet (CLI) SNMPv1/v2/v3 Single IP management RMON sFlow Monitoring 2. 1. 3 Physical Specification Mechanics Dimensions (W x H x D) Weight Heat transfer Air inlet Air outlet 440 mm x 55 mm x 310 mm 5. 0 Kg - on the right side of the system - on the left side of the system Environmental Conditions Operating temperature Storage temperature Operating humidity Interface Parameter VDSL subscriber i/f Splitter for narrowband services Ethernet i/f (modular, optical) Ethernet i/f (fixed, electrical) Ethernet i/f for local management Serial i/f, Console RJ21 RJ21 2-Port 100/1000Base-X (SFP type) 1-Port GE-PON + 1-Port 1000Base-X 10/100/1000Base-T 10/100Base-TX RS232 0 to +50 °C -40 to +70 °C 0 to 95 % (non-condensing) SMC7824M/VSW 15 IMN Installation Manual TigerAccessTM EE Power Supply AC power voltage Maximum power consumption 100-240VAC, 50/60Hz 85W (with 2-Port SFP option module) 88W (with 1-Port GE-PON + 1-Port SFP option module) Operating Indicators System LEDs VDSL i/f LEDs Uplink i/f LEDs Console MGMT RUN / FAN / PWR L/A L/A, 1G (1000Base-X, SFP) LNK (GE-PON) RX / TX LNK / ACT 2. 2 Operating Status LEDs Fig. 2. 3 LEDs of the Switch You can easily find product condition through LEDs that indicate operating state of the equipment on the front panel. And you need to know how to operate this product. The LED indicators show an error or a normal operation of the system. Basically, the following table provides the description of all LEDs of the switch. Label RUN Color Green Status On Blinking Off Amber FAN Amber Blinking Off Blinking PWR Green On Off Description The system is starting up or frozen. Power voltage is currently fed to the system. Power voltage is not fed to the system. Tab. 2. 2 Operating Status LEDs on the switch 16 SMC7824M/VSW Installation Manual TigerAccessTM EE IMN Status LEDs for VDSL Interfaces Label 1-24 Color Green Status On Blinking Off Description The interface is connected to a CPE. The interface is starting to be connected to a CPE. The interface is not connected to a CPE. Tab. 2. 3 Status LEDs for VDSL Interfaces Status LEDs for Console Interface Label TX Color Green Status Blinking Off RX Green Blinking Off Description A transmit activity is present on the console. [. . . ] Connect the other end of the power cable to AC power supply. 5. 8 describes how to connect the AC power cable. Fig. 5. 8 Connecting the AC Power Cable !! Make sure the power switch is in the OFF position before connecting. [. . . ]