User manual SMC 9712GSMT/2

[. . . ] In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures. CONTENTS Package Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Chapter 1 1. 1 1. 2 Product Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Product Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Chapter 2 2. 1 2. 2 Identifying External Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Rear Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Chapter 3 3. 1 3. 2 3. 2. 1 3. 2. 2 3. 3 3. 4 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Desktop Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Rack Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Connect to Ground . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Power on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Appendix A: Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Appendix B: Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Package Contents The following contents should be found in your package: One SMCFS1601 /SMC9712GSMT/2 Switch One power cord This User Guide Mounting screws and two "L" planks Quick Installation Guide SMC Warranty Card Four rubber foot pads Note: Make sure that the package contains the above items. If any of the listed items are damaged or missing, please contact with your distributor. 1 Chapter 1 Product Introduction This chapter describes the features of the model of SMCFS1601/SMC9712GSMT/2 16/24-Port 10/100Mbps Fast Ethernet Switch. 1. 1 Product Overview SMCFS1601/SMC9712GSMT/2 Switch provides 16/24-Port 10/100Mbps AutoNegotiation RJ45 ports. Each port of the SMCFS1601/SMC9712GSMT/2 supports auto MDI/MDI-X function, eliminating the need for crossover cables or Uplink ports. [. . . ] The SMCFS1601/SMC9712GSMT/2 16/24-port 10/100Mbps Fast Ethernet Switch provides you with a low-cost, easy-to-use, high-performance, seamless and standard upgrade to improve your old network to a 100Mbps network. It will boost your network performance up to full duplex data transfer. 1. 2 Features Complies with IEEE802. 3, IEEE802. 3u standards 16/24 10/100Mbps Auto-Negotiation RJ45 ports supporting Auto- MDI/MDIX Supports IEEE802. 3X flow control for full-duplex mode and backpressure for half-duplex mode LED indicators for monitoring power, link, activity, speed Rack-mountable steel case Internal power supply Chapter 2 Identifying External Components This Chapter describes the front panel, rear panel and LED indicators of the Switch. SMCFS1601/SMC9712GSMT/2 just differ in the number of LED indicators and ports, and all figures in this guide are of SMC9712GSMT/2. 2 2. 1 Front Panel The front panel of SMC9712GSMT/2 consists of switch model, switch LED indicators, and 24 10/100Mbps RJ-45 ports. Figure 2-1 SMC9712GSMT/2 Switch Front Panel sketch The LED indicators include Power, Link/Act LED indicators, which are used for monitoring and pre-troubleshooting of the Switch. The following section shows the LED indicators of the Switch along with an explanation of each indicator. Power LED: This indicator will light solid green when the Switch powers up. If the LED is not lit, please check the power supply and connection. Link/Act LED: The LED indicates Link/Active status. The corresponding LED indicator will light solid green when connected to a network device. It flashes green when data is being transmitted or received on the working connection. 2. 2 Rear Panel The rear panel of SMC9712GSMT/2 features a power socket and a Grounding Terminal (marked with ). Figure 2-2 SMC9712GSMT/2 Switch Rear Panel sketch Grounding Terminal: SMCFS1601/SMC9712GSMT/2 already comes with Lightning Protection Mechanism. Position the Switch away from water and moisture sources, be sure to provide an acceptable temperature and humidity operating environment. 4 3. 2 Installation This Switch can be either installed on the standard 19-inch mountable rack or located on the desktop. Caution: Please unplug the power cord before installing or removing the Switch. 3. 2. 1 Desktop Installation To install the Switch on the desktop, please follow the steps: 1) Set the Switch on a flat surface strong enough to support the entire weight of the Switch with all fittings. 2) Remove the adhesive backing papers from the rubber feet. 3) Turnover the Switch and attach the supplied rubber feet to the recessed areas on the bottom at each corner of the Switch. Figure 3-1 Attaching Rubber Feet 4) Upturn the Switch and connect it to the network devices while keep enough ventilation space around. 5) Connect the Switch to power source with the provided power cord. Caution: Please avoid any heavy thing placed on the Switch. 5 3. 2. 2 Rack Installation To install the Switch in an EIA standard-sized, 19-inch rack, follow the instructions described below: 1) Secure the supplied rack-mounting brackets to each side of the Switch with supplied screws, as illustrated in the following figure. Figure 3-2 Attaching Brackets 2) After the brackets are attached to the Switch, use suitable screws (not provided) to secure the brackets to the rack, as illustrated in the following figure. Figure 3-3 Mounting Switch 3) Connect the Switch to network devices. 4) Supply power to the Switch with the provided power cord. 6 3. 3 Connect to Ground Connecting the Switch to ground is to quickly release the lightning over-voltage and over-current of the Switch, which is also a necessary measure to protect the body from electric shock. In different environments, the Switch may be grounded differently. The following will instruct you to connect the Switch to the ground in two ways, connecting to the Grounding Bar or connecting to the Ground via the power cord. [. . . ] Please connect the Switch to ground in the optimum way according to your specific operation environment. · Connecting to the Grounding Bar If the Switch is installed in the Equipment Room, where a Grounding Bar is available, you are recommended to connect the Switch to the Grounding Bar as shown in the following figure. Figure 3-4 Note: The Grounding Bar and Ground Cable are not provided with our product. · Connecting to the Ground via the power supply If the Switch is installed in the normal environment, the Switch can be grounded via the PEProtecting Earthcable of the AC power supply as shown in the following figure. 7 Figure 3-5 * The figure is to illustrate the application and principle. [. . . ]