User manual SMC WBR14-G

[. . . ] BarricadeTM g 2. 4 GHz 54 Mbps Wireless Cable/DSL Broadband Router From SMC's Barricade line of Broadband Routers 38 Tesla Irvine, CA 92618 Phone: (949) 679-8000 December 2004 Revision Number: R01 COPYRIGHT Information furnished by SMC Networks, Inc. (SMC) is believed to be accurate and reliable. However, no responsibility is assumed by SMC for its use, nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of SMC. [. . . ] Manual Connect: When the connection is broken by the idle time, you must press Connect button on the Status page to reconnect. Connect On Demand: When the connection is broken by the idle time, any trigger can make the connection alive. If you are on a leased line or pay-per min. connection, please set your maximum idle time to 3 minutes. This will cause your Internet connection to drop after 3 minutes of idle time so you won't be charged for extra online time from your ISP. · Note: Click FINISH to complete the setup. BigPond If you use the BigPond Internet Service which is available in Australia, enter the the User Name, Password and Authentication Service Name for BigPond authentication. Click FINISH to complete the setup. 29 Configuring the Wireless Barricade g Router Advanced Setup Use the web management interface to define system parameters, manage and control the Wireless Barricade and its ports, or monitor network conditions. The following table outlines the selections available. Menu System Description Sets the local time zone, the password for administrator access, the Internet security of ZoneAlarm Pro (optional), system log server, and the IP address of a PC that will be allowed to manage the Wireless Barricade remotely. Specifies the Internet connection type: · Dynamic IP host configuration and the physical MAC address of each media interface · PPPoE configuration · PPTP configruation · Static IP and ISP gateway address · BigPond (Internet service available in Australia) · Specifies DNS servers to use for domain name resolution. WAN LAN Wireless NAT Firewall DDNS UPnP Sets the TCP/IP configuration of the Wireless Barricade's LAN interface and all DHCP clients. Configures the radio frequency, SSID, encryption and 802. 1x security, and WDS for wireless communications. Shares a single ISP account with multiple users, sets up virtual servers. Configures a variety of security and specialized functions, including: Access Control, Hacker Prevention, and DMZ. Dynamic DNS provides users on the Internet with a method to tie their domain name to a computer or server. With Universal Plug and Play, a device can automatically join a network, obtain an IP address, communicate its capabilities, and learn about the presence and capabilities of other devices. Devices can then directly communicate with each other. This further enables peer-to-peer networking. 30 Advanced Setup Menu Tools Description Contains options to back up and restore the current configuration, restore all configuration settings to the factory defaults, update system firmware, or reset the system. Provides WAN connection type and status, firmware and hardware version numbers, system IP settings, as well as DHCP, NAT, and Firewall information. Displays the number of attached clients, the firmware versions, the physical MAC address for each media interface, and the hardware version and serial number. Shows the security and DHCP client log. Status 31 Configuring the Wireless Barricade g Router System Time Zone Set the time zone and time server for the Wireless Barricade. This information is used for log entries and client access control. · Set your local time zone settings Select your time zone from the drop-down list, and set the start and end dates if your area requires daylight savings. To automatically update the Wireless Barricade's internal clock by synchronizing with a public time server over the Internet, choose one of the methods below. 32 Advanced Setup · Get date and time from online time servers (Network Time Protocol) Choose the online standard time server for your area from the drop-down menu, or enter the IP address of the time server on your network. [. . . ] Once you have confirmed that your computer is configured for DHCP, then please follow the steps below. Open a DOS window as described above. 82 Troubleshooting 2. The 10/100 LED does not light after a connection is made. Check that the host computer and the Wireless Barricade are both powered on. [. . . ]