User manual SMC SMCWGBR14-N2

[. . . ] USER GUIDE BARRICADETM N 802. 11n Wireless 4-port Gigabit Broadband Router SMCWGBR14-N2 BarricadeTM N SMCWGBR14-N2 User Guide No. 1, Creation Road III, Hsinchu Science Park, 30077, Taiwan, R. O. C. TEL: +886 3 5770270 Fax: +886 3 5780764 September 2011 SMC-UG-0911-02 Information furnished by SMC Networks, Inc. (SMC) is believed to be accurate and reliable. [. . . ] Click Finish to complete the WPS configuration. Figure 49: The WPS Configuration Screen of Wireless Adapter ­ 66 ­ CHAPTER 6 | Wireless Settings WPS Method Three: 1. Keep the default WPS Status as Enabled and click the Add device button in Figure 44, then the following screen will appear. Figure 50: Add a New Device 2. Choose Press the button of the new device in two minutes and click Connect. 3. For the configuration of the wireless adapter, please choose Push the button on my access point in the configuration utility of the WPS as below, and click Next. Figure 51: The WPS Configuration Screen of Wireless Adapter ­ 67 ­ CHAPTER 6 | Wireless Settings WPS 4. Wait for a while until the next screen appears. Click Finish to complete the WPS configuration. Figure 52: The WPS Configuration Screen of Wireless Adapter ­ 68 ­ CHAPTER 6 | Wireless Settings WPS By PIN If the new device supports Wi-Fi Protected Setup and the PIN method, you can add it to the network by PIN with the following two methods. Method One: Enter the PIN into my Router 1. Keep the default WPS Status as Enabled and click the Add device button in Figure 44, then the following screen will appear. Figure 53: Add a New Device 2. Choose Enter the new device's PIN and enter the PIN code of the wireless adapter in the field behind PIN in the above figure. NOTE: The PIN code of the adapter is always displayed on the WPS configuration screen. 3. For the configuration of the wireless adapter, please choose Enter a PIN into my access point or a registrar in the configuration utility of the WPS as below, and click Next. ­ 69 ­ CHAPTER 6 | Wireless Settings WPS Figure 54: The WPS Configuration Screen of Wireless Adapter NOTE: In this example, the default PIN code of this adapter is 26499123 as the above figure shown. Method Two: Enter the PIN from my Router 1. Here takes the PIN code 12345670 of this Router for example). 2. For the configuration of the wireless adapter, please choose Enter a PIN from my access point in the configuration utility of the WPS as below, and enter the PIN code of the Router into the field behind Access Point PIN. Then click Next. ­ 70 ­ CHAPTER 6 | Wireless Settings WPS Figure 55: The WPS Configuration Screen of Wireless Adapter NOTE: The default PIN code of the Router can be found in its label or the WPS configuration screen as Figure 44. 3. Then the new device successfully connected to the network. NOTE: The status LED on the Router will light green all the time if the device has been successfully added to the network. The WPS function cannot be configured if the Wireless Function of the Router is disabled. Please make sure the Wireless Function is enabled before configuring the WPS. ­ 71 ­ 7 DHCP SETTINGS There are three submenus under the DHCP menu: DHCP Settings, DHCP Clients List and Address Reservation. Click any of them, and you will be able to configure the corresponding function. DHCP SETTINGS Choose menu "DHCP->DHCP Settings", you can configure the DHCP Server on the page. The Router is set up by default as a DHCP (Dynamic Host Configuration Protocol) server, which provides the TCP/IP configuration for all the PC(s) that are connected to the Router on the LAN. Figure 56: DHCP Settings DHCP Server - Enable or Disable the DHCP server. If you disable the Server, you must have another DHCP server within your network or else you must configure the computer manually. Start IP Address - Specify an IP address for the DHCP Server to start with when assigning IP addresses. [. . . ] IEEE 802. 11g is also backward compatible with IEEE 802. 11b. IEEE 802. 11N A wireless standard that supports wireless communications in the 2. 4 GHz band using Orthogonal Frequency Division Multiplexing (OFDM). The standard provides for data rates of 27, 54, 81, 108, 162, 216, 243, 270, 300 Mbps. IEEE 802. 11n is also backward compatible with IEEE 802. 11b/g. DDNS (DYNAMIC The capability of assigning a fixed host and domain name to a dynamic DOMAIN NAME SYSTEM) Internet IP Address. DHCP Dynamic Host Configuration Protocol: Provides a framework for passing configuration information to hosts on a TCP/IP network. [. . . ]