User manual SMEG 1253L

[. . . ] Always turn hood ON when cooking at high heat or when flambéing food (i. e. Crepes Suzette, Cherries Jubilee, Peppercorn Beef Flambé). Grease should not be allowed to accumulate on fan or filter. Always use cookware appropriate for the size of the surface element. [. . . ] A hole cut through wood must be sanded until smooth. A hole through metal must have a grommet. WARNING - TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, do not use this fan with any solid-state speed control device. WARNING - TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: Use this unit only for the purpose intended by the manufacturer. If you have any questions, contact the manufacturer. Before servicing or cleaning the unit, switch power off at service panel and lock the service disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel. CAUTION: For General Ventilating Use Only. Do Not Use To Exhaust Hazardous or Explosive Materials and Vapors. EN 4 4 WARNING - TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: Installation Work And Electrical Wiring Must Be Done By Qualified Person(s) In Accordance With All Applicable Codes And Standards, Including Fire-Rated Construction. Sufficient air is needed for proper combustion and exhausting of gases through the flue (chimney) of fuel burning equipment to prevent backdrafting. Follow the heating equipment manufacturer's guideline and safety standards such as those published by the National Fire Protection Association (NFPA), and the American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE), and the local code authorities. When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities. Ducted fans must always be vented to the outdoors. WARNING · Electrical ground is required on this rangehood. · If cold water pipe is interrupted by plastic, nonmetallic gaskets or other materials, DO NOT use for grounding. · DO NOT have a fuse in the neutral or grounding circuit. A fuse in the neutral or grounding circuit could result in electrical shock · Check with a qualified electrician if you are in doubt as to whether the rangehood is properly grounded. · Draw a horizontal line at 24" above the hob. · Place bracket 7. 2. 1 on the wall as shown about 1/16" from the ceiling or upper limit aligning the center (notch) with the vertical reference line. · Mark the wall at the centers of the holes in the bracket. · Place bracket 7. 2. 1 on the wall as shown at X" below the first bracket (X = height of the upper chimney section supplied), aligning the center (notch) with the vertical line. · Mark the wall at the centers of the holes in the bracket. · Mark a reference point as indicated at 4" 9/16 from the vertical reference line and 13" 3/8 above the horizontal reference line. · Repeat this operation on the other side. · Drill ø 5/16" holes at all the center points marked. · Insert the wall plugs 11 in the holes. · Fix the brackets using the 12a screws supplied. · Insert the two screws 12a supplied in the hood body fixing holes, leaving a gap of 3/16 " between the wall and the head of the screw. 24" 12"5/8 X 7. 2. 1 EN 8 8 Mounting the hood body · Before attaching the hood body, tighten the two screws Vr located on the hood body mounting points. [. . . ] Attach the White lead of the power supply to the White lead of the rangehood with a twist-on type wire connector. Attach the Black lead of the power supply to the Black lead of the rangehood with a twist-on type wire connector. · Replace the cover. Green Ground screw Ground wire Power supply cable Chimney assembly Upper exhaust chimney · Slightly widen the two sides of the upper flue and hook them behind the brackets 7. 2. 1, making sure that they are well seated. · Secure the sides to the brackets using the 4 screws 12c supplied. [. . . ]