User manual SMEG 6091TF

[. . . ] Adaptation to different types of gas ____________________ 25 5. 1 5. 2 5. 3 5. 4 5. 5 5. 6 5. 7 5. 8 5. 9 Removing the hob top________________________________________________25 Adjustment for liquid gas _____________________________________________26 Adjustment for natural gas ____________________________________________26 Primary air adjustment _______________________________________________26 Re-assembling the hob top____________________________________________27 Adjusting the minimum setting for natural gas _____________________________27 Adjusting the minimum setting for liquid gas_______________________________27 Arrangement of the burners on the hob __________________________________27 Lubrication of gas taps _______________________________________________27 6. Description of the controls ___________________________ 28 6. 1 The front panel _____________________________________________________28 7. Using the hob _____________________________________ 29 7. 1 7. 2 7. 3 7. 4 Positioning the racks_________________________________________________29 Lighting the burners using a safety device ________________________________31 Practical tips for using the burners ______________________________________31 Pan diameters______________________________________________________32 8. Cleaning and maintenance___________________________ 33 8. 1 Cleaning the hob____________________________________________________33 8. 2 Cleaning instructions fora n acid-et ched glass hob _________________________33 8. 3 Cleaning parts______________________________________________________33 THESE INSTRUCTIONS ARE VALID ONLY FOR THE DESTINATION COUNTRIES WHOSE IDENTIFYING SYMBOLS ARE INCLUDED ON THE COVER OF THIS MANUAL. [. . . ] SEPARATE THE VARIOUS WASTE PACKAGING MATERIALS AND CONSIGN THEM TO THE NEAREST DIFFERENTIATED COLLECTION CENTRE. THE APPLIANCE MUST BE EARTHED IN COMPLIANCE WITH ELECTRICAL SYSTEM SAFETY REGULATIONS. THE PLUG TO BE CONNECTED TO THE SUPPLY CABLE AND THE RELEVANT SOCKET MUST BE OF THE SAME TYPE AND CONFORM TO THE REGULATIONS IN FORCE. B). 2. 4 Inserting the hob into the hole in the work surface Be very careful when inserting the hob. If the process is not followed correctly as described, the hob may be damaged. Before inserting it, remove the racks (if they are mounted) and burners from the hob. Insert the hob, resting the frame completely on the back edge of the hole in the work surface. Do not apply pressure to the frame as this part is very fragile and could be damaged. Then lower the front of the hob until it is fully inserted. 22 Instructions for the installer 3. Electrical connection Make sure that the voltage and capacity of the power line conform to the data shown on the plate located under the casing. Do not remove this plate for any reason. The plug at the end of the supply cable and the wall socket must be of the same type and must conform to the applicable legislation on electrical installations. Make sure that the supply line is suitably earthed. Pass the power supply cable through the back of the unit, taking care that it does not touch the bottom casing of the hob or the oven (if any) installed underneath it. Fit the power line with an omnipolar circuit-breaker with a contact opening gap equal to or greater than 3 mm, in an easily accessible position close to the appliance. Avoid the use of adapters and shunts. If the power cable is replaced, the cross-section of wires in the new cable must be no less than 0. 75 mm2 (3 x 0. 75 cable), remembering that the end for connection to the appliance must have an earth wire (yellow/green) which is at least 20 mm longer. Only use a H05V2V2-F or similar cable resistant to temperatures of up to 90°C. If other types of gas are to be used, the nozzles must be replaced and the primary air must be adjusted. In order to replace the nozzles and adjust the burners, the hob top must be removed as described below. 5. 1 Removing the hob top Remove all the burner components, following the numerical sequence in the figures below: · · Take out all the knobs by pulling them upwards. Lift all the burner components off the hob. 1 · Remove the couvette from each burner by unscrewing the two screws. 2 · Remove the hob fastening screws, taking care to remove only the screws shown in the figure to the right. 3 · Having removed all the components described above, lift the hob top upwards. 4 25 Instructions for the installer 5. 2 Adjustment for liquid gas Unscrew screw C and push air regulator D as far as it will go. Using a 7-mm wrench, remove nozzle E and replace it with the appropriate nozzle, following the instructions in the tables for the type of gas to be used. The nozzle tightening torque must be no more than 3 Nm. Adjust the air by sliding regulator D until distance "X" from the table in "5. 4 Primary air adjustment" is reached. After adjustment with a gas other than the preset one, replace the label on the casing of the appliance with the label corresponding to the new gas. The label is located inside the GPL nozzle pack (G30 ­ G31). 5. 8 Arrangement of the burners on the hob Type of burner 1 2 3 4 Auxiliary Semi-rapid Rapid Ultra-rapid 5. 9 Lubrication of gas taps Over time the gas taps may become difficult to turn and get blocked. Clean them internally and replace the lubrication grease. This procedure must be carried out by a specialised technician. 27 Instructions for the user 6. Description of the controls CONTROL ZONE 6. 1 The front panel All the hob controls are grouped together on the front panel. 4-burner hob KNOB DESCRIPTION To light the flame, press the knob and, at the same time, turn it anticlockwise to the minimum flame symbol . [. . . ] The appliance is equipped with electronic ignition. Simply press the knob and simultaneously turn it anticlockwise to the minimum flame symbol , until it lights. Hold down the knob for about 2 seconds to keep the flame lit and to activate the safety device. The burner may go out when the knob is released. [. . . ]