User manual SMEG 6092

[. . . ] INSTALLATION MUST BE CARRIED OUT BY QUALIFIED PERSONNEL IN ACCORDANCE WITH THE REGULATIONS IN FORCE. THIS APPLIANCE IS INTENDED FOR DOMESTIC USE AND CONFORMS TO THE EC DIRECTIVES CURRENTLY IN FORCE. THE APPLIANCE HAS BEEN BUILT TO CARRY OUT THE FOLLOWING FUNCTIONS: COOKING AND HEATING UP FOOD; ALL OTHER USES ARE CONSIDERED UNSUITABLE. THE MANUFACTURER CANNOT BE HELD LIABLE FOR USES OTHER THAN THOSE INDICATED. [. . . ] If the process is not followed correctly as described, the hob may be damaged. Before inserting it, remove the racks (if they are mounted) and burners from the hob. Insert the hob, resting the frame completely on the back edge of the hole in the work surface. Do not apply pressure to the frame as this part is very fragile and could be damaged. Then lower the front of the hob until it is fully inserted. 22 Instructions for the installer 3. Electrical connection Make sure that the voltage and capacity of the power line conform to the data shown on the plate located under the casing. Do not remove this plate for any reason. The plug at the end of the supply cable and the wall socket must be of the same type and must conform to the applicable legislation on electrical installations. Make sure that the supply line is suitably earthed. Pass the power supply cable through the back of the unit, taking care that it does not touch the bottom casing of the hob or the oven (if any) installed underneath it. Fit the power line with an omnipolar circuit-breaker with a contact opening gap equal to or greater than 3 mm, in an easily accessible position close to the appliance. Avoid the use of adapters and shunts. If the power cable is replaced, the cross-section of wires in the new cable must be no less than 0. 75 mm2 (3 x 0. 75 cable), remembering that the end for connection to the appliance must have an earth wire (yellow/green) which is at least 20 mm longer. Only use a H05V2V2-F or similar cable resistant to temperatures of up to 90°C. The replacement must be made by a specialist technician who must implement the connection to the power grid according to the diagram below. L = brown N = blue = yellow/green The power supply cable must be replaced by an authorised service centre to prevent any risks. The manufacturer cannot be held liable for damage to persons or things caused by non-observance of the above directions or by interference with any part of the appliance. 23 Instructions for the installer 4. Lift all the burner components off the hob. 1 · Remove the couvette from each burner by unscrewing the two screws. 2 · Remove the hob fastening screws, taking care to remove only the screws shown in the figure to the right. 3 · Having removed all the components described above, lift the hob top upwards. 4 25 Instructions for the installer 5. 2 Adjustment for liquid gas Unscrew screw C and push air regulator D as far as it will go. Using a 7-mm wrench, remove nozzle E and replace it with the appropriate nozzle, following the instructions in the tables for the type of gas to be used. The nozzle tightening torque must be no more than 3 Nm. Adjust the air by sliding regulator D until distance "X" from the table in "5. 4 Primary air adjustment" is reached. After adjustment with a gas other than the preset one, replace the label on the casing of the appliance with the label corresponding to the new gas. The label is located inside the GPL nozzle pack (G30 ­ G31). 5. 8 Arrangement of the burners on the hob Type of burner 1 2 3 4 Auxiliary Semi-rapid Rapid Ultra-rapid 5. 9 Lubrication of gas taps Over time the gas taps may become difficult to turn and get blocked. Clean them internally and replace the lubrication grease. This procedure must be carried out by a specialised technician. 28 Instructions for the user 6. Description of the controls CONTROL ZONE 6. 1 The front panel All the hob controls are grouped together on the front panel. 4-burner hob KNOB DESCRIPTION To light the flame, press the knob and, at the same time, turn it anticlockwise to the minimum flame symbol . To adjust the flame, turn the knob to the zone between the maximum ( ) and minimum ( ) settings. To turn off the burner, turn the knob to the O position. KNOB-BURNER ASSOCIATION 29 Instructions for the user 7. [. . . ] Use ordinary non-abrasive products for glass, together with anti-scratch sponges and wooden or plastic utensils if necessary. Rinse thoroughly and dry with a soft cloth or chamois leather. 8. 2 Cleaning instructions fora n acid-et ched glass hob 8. 2. 1 Grease Use washing up liquid and a microfibre cloth. 8. 2. 2 Rings and encrustations Use stainless steel cream or mildly abrasive creams; leave the product to act for a few minutes, then wipe away with a microfibre cloth. 8. 2. 3 Stubborn encrustations If using the microfibre cloth is not enough, a brass wire sponge can be used together with stainless steel cream or standard abrasive creams available in shops. [. . . ]