User manual SMEG 6096BC

[. . . ] ALWAYS CHECK THAT THE CONTROL KNOBS ARE IN THE POSITION WHEN YOU FINISH USING THE HOB. (OFF) THE IDENTIFICATION PLATE, WITH TECHNICAL DATA, SERIAL NUMBER AND MARKING IS CLEARLY VISIBLE UNDER THE CASING. THE PLATE ON THE CASING MUST NOT BE REMOVED. 22 Introduction DO NOT PUT PANS WITHOUT PERFECTLY SMOOTH AND FLAT BOTTOMS ON THE COOKING HOB GRIDS. DO NOT USE RECIPIENTS OR GRIDDLE PLATES THAT EXTEND BEYOND THE EXTERNAL PERIMETER OF THE HOB. THE HOB IS TO BE USED BY ADULTS ONLY. DO NOT LET UNSUPERVISED CHILDREN PLAY WITH THE HOB. THIS APPLIANCE IS MARKED ACCORDING TO THE EUROPEAN DIRECTIVE 2002/96/EC ON WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT (WEEE). [. . . ] The left opening must be used for gas connections, and the right one for electrical connections. Before securing the hob to the supporting base, make 4 holes 8mm in diameter at the indicated points through which the screws will pass that are to be secured into the rivets in the bottom part of the product. 35 mm 100 mm 490 mm 200 mm 90 mm 90 mm 150, 1 mm 119. 9 mm The interaxes of the holes and the dimensions of the openings refer to a hob installed against the back wall. Ø 8 m m Ø 8 m m Ø 8 m m Z 660 mm 300 mm Ø 8 m m 26 Instructions for the installer 2. 5 Mounting for type A installations Once the hob is correctly positioned in its support, place the brackets (A) over the bottom part of the product (B). Attachment requires 2 brackets for each side of the hob. 1) Secure the brackets to the walls of the base by screwing the supplied screws through the appropriate holes (C). These operations will guarantee that the entire product is mounted in a stable way. 2) Important: for fixing the product, use the supplied brackets in all the fixing points. 27 Instructions for the installer 2. 6 Mounting for type B installations Once the hob is correctly positioned on the supporting base, complete the mounting by tightening the product using the 4 supplied metric screws, by screwing them through the 8mm Ø holes made before installation. Make sure that the holes on the structure are centred with those on the bottom of the product. Important: other types of installation are possible if supervised by the manufacturer. Important: for fixing this product to the support structure, you are advised not to use mechanical or electrical screwdrivers and to exert moderate pressure by hand on the mounting parts. If this product is installed over an oven, the oven must have a cooling fan. 28 Instructions for the installer 2. 7 Electrical connection Make sure that the voltage and capacity of the power line conform to the data shown on the plate located under the casing. Do not remove this plate for any reason. The plug on the end of the supply cable and the wall socket must be the same type and conform to the current electrical system regulations. Check that the power line is adequately grounded. On the power line, install an omnipolar cut-off device with contact cut-off distance greater than or equal to 3 mm, located in an easily accessible position near the unit. To change the nozzles, proceed as described below. 3. 1 Replacement of nozzles on the hob This operation requires no primary air regulation. Extract the grids and remove all the caps and flame-spreader crowns; 2. unscrew the burner nozzles with a 7 mm socket wrench; 3. replace the nozzles according to the type of gas to be used and the description in paragraph "3. 2 Burner and nozzle characteristics table". Replace the burners in the correct position. 32 Instructions for the installer 3. 2 Burner and nozzle characteristics table Burner Rated heating capacity (kW) Nozzle diameter 1/100 mm 50 65 75 100 LPG ­ G30/G31 28/37 mbar Auxiliary Semi rapid Rapid Ultrarapid 1. 05 1. 75 2. 3 3. 9 Rated heating capacity (kW) By-pass mm 1/100 30 33 45 65 Reduced flowrate (W) 400 500 800 1600 Flowrate g/h G30 76 130 166 284 Flowrate g/h G31 75 128 164 279 Burner Natural gas ­ G20 20 mbar Auxiliary Semi rapid Rapid Ultrarapid 1. 05 1. 75 2. 3 3. 9 Nozzle diameter 1/100 mm 72 97 103 135 Reduced flowrate (W) 400 500 800 1600 3. 3 Arrangement of burners on cooking hob BURNERS 1 2 3 4 Auxiliary Semi rapid Rapid Ultrarapid 33 Instructions for the installer 4. FINAL OPERATIONS Having carried out the above adjustments, reassemble the appliance following, backwards, the instructions in paragraph "3. 2 Burner and nozzle characteristics table". After adjustment to a different kind of gas from the one for which the cooker has been tested, replace the plate inside the heating compartment with one corresponding to the new kind of gas. This plate can be obtained from your nearest Authorised Assistance Centre. 4. 1 Adjustment of minimum for natural gas Light the burner and take it to the minimum. Remove the gas tap knob and turn the adjustment screw inside or at the side of the tap shaft (depending on the model) until there is a regular minimum flame. Replace the knob and check burner flame stability: (rapidly turning the knob from maximum to minimum position, the flame should not go out). Repeat the operation on all the gas taps. 4. 2 Regulation of minimum for LPG To regulate the minimum for LPG, completely tighten (clockwise) the screw inside or next to the gas tap pin (depending on the model). [. . . ] Panstand grid B, available upon request, is intended for use with woks (Chinese pans). To prevent damage to the worktop, the hob is equipped with a raised grid C: installs over pans larger than the diameter shown in the table in paragraph " 5. 3 Diameter of receptacles". Note that pans larger than 28 cm diameter must be used only on the central burner. 5. 1 Lighting the burners Each knob corresponds to the burner indicated. The appliance is equipped with an electric lighting device. [. . . ]