User manual SMEG 7520EB

[. . . ] THE MANUFACTURER DECLINES ALL RESPONSIBILITY FOR INJURY OR DAMAGE CAUSED BY FAILURE TO COMPLY WITH THE ABOVE REGULATIONS OR DERIVING FROM INCORRECT USE, TAMPERING WITH EVEN JUST ONE PART OF THE APPLIANCE AND THE USE OF NON-ORIGINAL SPARE PARTS. THE APPLIANCE MUST BE IN COMPLIANCE WITH ELECTRICAL SYSTEM SAFETY REGULATIONS. THIS APPLIANCE IS TAGGED UNDER EUROPEAN DIRECTIVE 2002/96/EC ON WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT (WEE). BY MAKING SURE THAT THIS PRODUCT IS DISPOSED OF CORRECTLY THE USER HELPS TO PREVENT POTENTIAL DETRIMENTAL EFFECTS ON HEALTH AND THE ENVIRONMENT. [. . . ] These switches must be installed close to the dishwasher, be easily accessible after installation, and provide complete disconnection from the electrical mains in overvoltage class III conditions. The dishwasher is always powered up unless the master switch is turned off. Connect the appliance to the user's earth system. The terminal for the connection is in the bottom right-hand corner of the appliance. The earth wire (PE) is yellow-green in colour, the neutral wire (N) is blue and the live wires (L1, L2, L3) are black, grey and brown. In the event of single-phase connection (230V-1N~) the connection to the electrical mains must be made using a cable with plug compliant with the relevant regulations. . IN THE EVENT OF DAMAGE TO THE SUPPLY CORD, HAVE IT REPLACED BY THE MANUFACTURER OR AN AUTHORIZED TECHNICAL SERVICE CENTRE IN ORDER TO AVOID ANY RISK. 7 8 5 START-UP FIRST START-UP The electrical protection system must undergo a functional test before the appliance is put into operation. The appliance must be installed and/or inspected by the qualified staff, who will start it up for the first time and provide the relevant operating instructions. PREPARING FOR USE Important: The rinse aid dispenser is fitted on all models, the detergent dispenser only on some. If both dispensers are present put the external detergent and rinse aid containers in place and insert the respective intake hoses on the rear of the machine into them. Red hose: detergent blue hose: rinse aid Before inserting the hoses into the containers, fit the weights (needed to ensure that they always draw in liquid from the bottoms of the containers) and the filters onto their ends as shown. If the detergent dispenser is not factory-fitted, it can be by ordering the relative kit. As an alternative an external dispenser can be fitted, making the electrical connection by means of an H05 RNF 2x0. 5 mm electrical cable, which can be laid along the route shown in the TECHNICAL DATA diagram and connected as shown in the wiring diagram supplied with the dishwasher. That the filters are in place, the spray arms rotate, and there are no foreign bodies in the dishwasher. Switch on the master switch (user): the word "OFF" appears on the display. 14 8. 3 FIRST USE EACH DAY (tank and boiler empty) Display shows Actions and what happens Door closed and master switch on ON: Press and hold down for 2-3 seconds; the L1 ON/OFF light and the two digits on the display light up. R The dishwasher fills the tank automatically. At the end of P this phase, when the tank is full, P appears on the display and program lights L5, L6, L7 are lit. WARNING!If the appliance is connected to cold water, wait at least 15' before moving on to the next phase to give the tank time to reach the correct washing temperature. Load the dishes and close the door. R 52 R Select the programme required by pressing one of the three buttons; the LED of the selected program flashes and the other two go out. The LED starts to flash and the washing cycle starts. While washing is in progress the display shows the water temperature in the tank. During rinsing, it shows the boiler temperature. At the end of the program the program LED comes on and "End" flashes on the display. Unload the dishes When the door is closed again, the system offers the last program run. 15 8. 4 Changing the program (not possible once the program has started) R 52 52 If the master switch is not turned off, the appliance offers the last cycle run. To change, press the button of the program required; the light comes on. R To confirm hold down for about 2". The LED starts to flash and the washing cycle starts. 9 CHOOSING THE PROGRAM PROGRAM P1 P2 P3 TYPE OF DIRT Glasses and cups Glasses, cups and plates with light dirt Very dirty dishes and cutlery Short 2' Average 2' 30" Long 3' DURATION (*) (*) The cycle duration stated above is guaranteed if the appliance is connected to hot water > 50°C <60°C If the dishwasher is supplied with cold water, the cycle duration might increase depending on the intake water temperature and the "thermostop" setting. LOADING THE DISHES Plates The equipment basket is able to take 8 plates. [. . . ] After removing the basket, undo the cap and pour the salt in using the funnel supplied. Remove any salt residues around the opening before screwing the cap back on. 17 10 MAINTENANCE AND CLEANING Although no particular scheduled maintenance is required, users are advised to have the dishwasher checked by a specialist technician twice a year. N. B. : the manufacturer accepts no liability for wilful damage or damage deriving from carelessness, neglect, failure to comply with instructions, regulations and standards or incorrect connections. 9. 2 Daily cleaning The dishwasher has IPX4 protection, but the use of direct water jets for cleaning is forbidden. Cleaning the filter during th day Remove the filters (simply lift them out as shown here), taking care that no large residues fall into the sump underneath. Clean them to remove residues and rinse with plenty of water, then put them correctly back in place; do not use sharp or pointed tools. [. . . ]