User manual SMEG A2D-6

[. . . ] Recommendations are given for the correct use of the baskets, spray arms, containers, filters, washing programs, and for operating the controls. Following the cleaning instructions provided here will keep your dishwasher's performance at peak levels in the long term. This user-friendly manual will provide answers to all your questions about use of the dishwasher. INSTALLATION INSTRUCTIONS: these are intended for the qualified technician who must carry out the installation, hook-up and testing of the appliance. USER INSTRUCTIONS: these consist of recommendations for using the appliance, a description of its controls and of the correct cleaning and maintenance procedures. 1 Safety instructions 1. [. . . ] In case that the door is opened during the operation, to the next door closing it is going to be necessary to start the program as shown in paragraph “STARTING THE PROGRAM”. The program will resume from the point in which it was interrupted. In case that the tub temperature is higher than 50°C the program will start about 60 seconds later. OPTION SELECTION Options are selected by pressing the relative button by the symbol of the option required; the light comes on to confirm that the option has been activated. • It is not possible to select any options when the soak program is being used. • All options except "Flexi Tabs" are disabled at the end of the wash cycle. To disable the “Flexi Tabs” option, press the relative button (the light goes out). • All options, including "Flexi Tabs" are disabled when a program is CANCELLED after it has begun. 18 User instructions "Flexi Tabs" The option is optimised for use of detergents which are complete with salt and rinse aid. With this option activated, any salt and rinse aid If you wish to use detergents which already contain salt and rinse aid already in the dishwasher will not be used. N. B. : even with the "Flexi Tabs" option selected, the regenerating salt/rinse aid lights will still stay on if their containers are empty. IMPORTANT: when no longer required, the option must be disabled by pressing the relative button (the light goes out). If the water hardness has been set on a value above H3, and the “Flexi Tabs” option is activated, the relative light flashes, warning of a setting error. Integrated products are not suitable for use with very "hard" water; this does not prevent the use of the option, but the washing results might not be of the best. Operating instructions Once the dishwasher has been correctly installed, prepare for use as follows: • • • Adjust the water softening system; Add the regenerating salt; Add the rinse aid and detergent. 4. 1 Using the water softening system The amount of scale contained in the water (water hardness index) can cause whitish staining on the dry dishes, which tend to become dull over time. The dishwasher is equipped with an automatic softening system which uses a special regenerating salt to reduce the hardness of the water. The dishwasher is factory set for water hardness level 3 (average hardness 4160° dF – 24-31° ). dH SALT When using water of medium hardness, the regenerating salt container should be refilled after approximately 20 washing cycles. The salt container can hold approximately 1. 7 Kg of salt in grains. The container is situated at the bottom of the dishwasher. After removing the lower basket, unscrew the salt container cap by turning it anticlockwise and pour in the salt using the funnel supplied with the dishwasher. Before replacing the cap, remove any salt residues from around the opening. • • When using the dishwasher for the first time, in addition to the salt it is also necessary to add one litre of water to the container. Each time the salt container is refilled, make sure that the cap is securely closed. The mixture of water and detergent must never penetrate the salt container, as this would compromise the operation of the regeneration system. [. . . ] Wash the arms under a jet of running water and return them carefully to their seat. After reassembly, check that the spray arms turn freely. Otherwise, check that they have been installed correctly. 34 User instructions CLEANING THE FILTER UNIT • • • • It is advisable to periodically inspect the centre filter C and, if necessary, to clean it. To remove the filter, grip the tabs, turn them anticlockwise and lift upwards; push the centre filter D from the underside to remove it from the microfilter: separate the two parts which make up the plastic filter by pressing the body of the filter in the zone shown by the arrows; remove the centre filter by lifting it upwards. GENERAL WARNINGS AND RECOMMENDATIONS FOR CORRECT MAINTENANCE: • The filters should be cleaned under running water using a stiff brush. [. . . ]