User manual SMEG ALVIKA20I

[. . . ] 28 CLEANING AND MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 EXTRAORDINARY MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 INSTRUCTIONS FOR THE USER: these contain user advice, description of the commands and the correct procedures for cleaning and maintenance of the appliance. INSTRUCTIONS FOR THE INSTALLER: these instructions are intended for the qualified technician who must perform the installation, put it into operation and test the appliance. 21 Instructions for safety and use 1. [. . . ] The cross-section of the wires of the new cable must not be less than 2. 5-1. 5 mm2 (4 x 2. 5 mm2 - 5 x 1. 5 mm2), remembering that the end to be connected to the oven must have an earth cable (yellow-green) that is at least 20 mm longer. 24 Instructions for the installer When linking up to mains by plug and socket, the connection must be completed with a three-core plug of adequate capacity (25A), or, for operation at 380-415V2N or 380-415V3N, a five-core plug (16A). The plug and wall-mounted socket must be of the same type (in accordance with CEI regulations). Make sure that the supply line is suitably earthed. If the appliance is connected to the electrical mains supply in a permanent manner, install a multipolar cut-out device on the line, with contact opening distance equal to or greater than 3 mm located near the appliance and in an easily reachable position. WARNING: if the phase voltage drops below 190 VAC, the performance of the oven may suffer, not due to the product itself. The terminal marked with this symbol connects parts together that are normally at zero potential. Connect the appliances appropriately using this terminal in order to make sure that they are equipotential. 2. 1. 1 Safety thermostat The oven is equipped with a safety device that takes action in case of serious malfunction. To re-arm the safety device you must contact the technical assistance service. The manufacturer declines all responsibility for damage to persons or things caused by the non-observance of the above prescriptions or deriving from tampering with any part of the appliance. 2. 2 Levelling Level the oven on the ground using the four adjustable feet. In order to adjust them, loosen the lock nut and unscrew the foot. The adjustment screws have a range of 10 mm. 25 Instructions for the installer 2. 3 Connection to the water mains (only in the steam model) aaaaaaaaaaa aaaaaaaaaaa Connect the water inlet socket on the back to a water socket with a threaded ¾ gas opening, taking care to screw it tightly to the hose. If the water piping is new or has been unused for a long time, before connection, run the water to make sure it becomes clear and free of impurities. Without this precaution, there is a risk that the water inlet will become clogged causing damage to the appliance. Press the "PUSH" knob: the display will show the cooking time. Turn the knob to the or symbols to set the cooking time (from 1 to 99 min). Only on the steam model, press the "PUSH" knob; the display will show the "H00" humidification cycle. Turn the knob to the or symbols to set the humidification from "H00" to "H10". Press the "PUSH" knob to exit from the data setting and saving phase. The message "PEnd" will appear on the display and the parameters will be saved. After 3 seconds the display will show the parameters set in rotation. To return to the "OFF" condition keep the "STOP" button pressed for 4 seconds. · · · 30 Instructions for the User 4. 6 Running a program From the "OFF" status proceed as follows: · Turn the knob to the or symbols to select one of the available programs from P01 to P38. The display will show the parameters of the selected program in rotation. To start the program press the "START" button. The appliance will perform a preheating cycle, showing the message "PrEh" on the display. [. . . ] Unlike saved programs, the cooking time can be set to infinite; the display will show the text "InF". · After saving it, DO NOT return to the "OFF" condition. Turn the knob to the or symbols to set the minutes. Press the "PUSH" button to exit from the data setting and saving phase. [. . . ]