User manual SMEG AP2640TC1

[. . . ] 9. INSTRUCTIONS FOR PROPER USE ______________________________________ 19 SAFETY INSTRUCTIONS _______________________________________________ 20 KNOW YOUR HOB ____________________________________________________ 21 BEFORE FIRST USE___________________________________________________ 21 COOKING ZONES_____________________________________________________ 22 DESCRIPTION OF CONTROL ON THE FRONT CONTROL PANEL______________ 23 USE OF THE COOKING HOB____________________________________________ 24 CLEANING AND MAINTENANCE _________________________________________ 28 SOMETHING WRONG?________________________________________________ 28 10. INSTALLATION _______________________________________________________ 29 INSTRUCTIONS FOR THE USER: these contain user advice, description of the commands and the correct procedures for cleaning and maintenance of the appliance. THE SYMBOLS SHOWN IN THIS MANUAL MAY DIFFER FROM THOSE ON THE PRODUCT. INSTRUCTIONS FOR THE INSTALLER: these are intended for the qualified technician who must install the appliance, set it functioning and carry out an inspection test. 18 Instruction for proper use 1. [. . . ] The lights go off upon temperature dropping to below approximately 60°C. 7. 1. 5 Switching off To turn off, return the knob to 0. 24 Instructions for the user 7. 2 Hobs with touch-control buttons When an icon is pressed the unit beeps to confirm. To operate the panel of the hobs equipped with touch-controls, lightly press the icons printed on its surface. On first connection to the electrical mains, an operating check will be carried out automatically and all the indicator lights will come on for a few seconds. 7. 2. 1 Switching on the hob for 2 seconds to switch the When not in use, all hob components will be switched off. Hold down hob on; a led will turn on above the symbol to confirm that the hob is lit. If no functions are used within 30 seconds of switching the hob on, it will automatically turn itself off. 7. 2. 2 Single cooking zones The relevant hotplate is indicated next to each control zone. For example, the symbol identifies the knob which controls the rear right-hand cooking zone. Having switched on the hob as described in "7. 2. 1 Switching on the hob", press the and keys to activate the hotplate (with the display indicating 0) and adjust the power to the desired operating setting. The operating power levels are 1 (lowest) to 9 (highest). The power must be set within 5 seconds of activating the hotplate as otherwise it will deactivate automatically. and as follows: To activate the hotplate and adjust its power level, press 1. Press (0 appears on the display to indicate that the hotplate has been activated); 2. Press again (9 appears on the display to indicate that the hotplate is active at the maximum power setting). or to increase or reduce the power to the desired level (1. . . 9). Press 7. 2. 3 Dual cooking zones To activate heating of the dual cooking zone, once power 9 is reached by following the instructions provided in paragraph "7. 2. 2 Single cooking zones", press the again. Now the maximum power of the cooking zone is activated, and is shown by the LED light turning on next to the number indicating and to adjust the power of the dual cooking zone to the operating power. 7. 2. 4 Triple cooking zones To activate heating of the triple cooking zone, once power 9 of the dual cooking zone is reached by following the instructions provided in paragraph "7. 2. 3 Dual cooking zones", press the again. Now the maximum power of the triple cooking zone is activated, and the LED indicating the operating power remains fix. Press and to adjust the power of the triple cooking zone to the desired value. on the symbols 7. 2. 5 Heating zone This zone, which is present only on some models in the range, keeps the area inside the dashed line at a temperature of approximately 90°C. It is used for warming dishes up or keeping them hot. [. . . ] IF A PLUG AND SOCKET CONNECTION IS BEING USED MAKE SURE THAT THE PLUG AND SOCKET ARE COMPATIBLE. AVOID USE OF ADAPTERS AND SHUNTS AS THESE COULD CAUSE OVERHEATING AND RISK OF BURNS. IF A FIXED CONNECTION IS BEING USED FIT POWER LINE WITH AN OMNIPOLAR CIRCUIT BREAKER WITH A CONTACT OPENING GAP EQUAL TO OR GREATER THAN 3 MM IN AN EASILY ACCESSIBLE POSITION IN PROXIMITY TO THE HOB. 29 Instructions for the installer For operation on 380-415 V 3N: use an - H05V2V2-F type five-core cable (5 x 1, 5 mm2). For operation on 380-415 V 2N: use an - H05V2V2-F type four-core cable (4 x 2, 5 mm2). For operation on 220-240 V 3: use an - H05V2V2-F type four-core cable (4 x 2, 5 mm2). For operation on 220-240 V: use an - H05V2V2-F type three-core cable. (3 x 4 mm2 : hob with 5 cooking zones) The cable end to be connected to the appliance must be provided with an earth wire (yellow-green) at least 20 mm longer. READ THE CONNECTION LAYOUT PLATE UNDERNEATH THE APPLIANCE WITH CARE. [. . . ]