User manual SMEG B603MFV

[. . . ] Adaptation to different types of gas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 4. Final operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Instructions for the user . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Description of controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 6. Use of the hob . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 7. [. . . ] The `cooking surface area' is defined as that part of the appliance where cooking normally takes place and does not include those parts of the appliance containing control knobs. For definition of hob, see Clause 1. 4. 64. For definition of trivet, see Clause 1. 4. 109. Consideration is to be given to window treatments when located near cooking appliances. Adaptation to different types of gas Before performing any cleaning or maintenance work, disconnect the appliance from the mains. The hob of the cooker is adjusted for use with either natural gas at a pressure of 1. 0kPa. In the case of operation with other types of gas the burner nozzles must be changed and the minimum flame adjusted on the gas taps. To change the nozzles, proceed as described below. 11 Instructions for the installer 3. 1 Replacement of nozzles on the hob This operation requires no primary air regulation. Extract the grids and remove all the caps and flame-spreader crowns; 2. unscrew the burner nozzles with a 7 mm socket wrench; 3. replace the nozzles according to the type of gas to be used and the description in paragraph "3. 2 Burner and nozzle characteristics table". The appliance has an electronic lighting device. Simply press and turn the knob anticlockwise to the minimum flame symbol , until the flame is lit. Hold the knob down for a few seconds to allow the thermocouples to heat up. The burner may go out when the knob is released: this is because the thermocouple has not been sufficiently heated. Repeat the operation holding down the knob a little longer. This operation is not necessary for burners without thermocouples. For models with thermocouples, should the burner accidentally go out, a safety device will be activated which stops the gas flow even if the tap is open. 19 Instructions for the user 6. 2 Practical advice for using the hob burners For better use of the burners and lower gas consumption, use covered vessel that are proportional in size to the burner to prevent the flame from heating the sides (see paragraph "6. 3 Diameter of the vessels to be used on each burner"). When water reaches the boiling point, lower the flame so that it doesn't overflow. To avoid burns or damage to the hob, all vessels or griddle plates must be placed within the perimeter of the hob. All vessels must have a flat and smooth bottom. [. . . ] Wash them in hot water with non-abrasive detergent, taking care to remove any encrustations, and wait until they are perfectly dry. WARNING: do not wash these components in the dishwasher. Replace the flame-spreader crowns, checking that they are positioned in their housing with their respective caps, taking care that flame-spreader holes A correspond to the spark plugs and the thermocouples. 10. 2. 3 The spark plugs and thermocouples To function properly the spark plugs and thermocouples must always be clean (on the models which are equipped with them). [. . . ]