User manual SMEG C8095

[. . . ] SAFETY PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . INSTALLING THE APPLIANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 4. 1 Wall fixing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 4. 2 Electrical connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] An efficient extraction system requires precision planning by a specialist qualified in this area and must comply with the positions and distances indicated by the applicable standards. When the job is complete, the installer must issue a certificate of conformity. 4. 5 Connection to gas 4. 5. 1 Connection with a rubber hose Installation of the standards-compliant rubber hose must be carried out so that the hose length is no greater than 1. 5 metres. Make sure that the hose does not come into contact with moving parts and is not squashed. The inside diameter of the hose must be 8 mm for LIQUID GAS and 13 mm for NATURAL GAS and TOWN GAS. Verify that all the following conditions are met: · the hose is fixed to the hose connection with safety clamps; · no part of the hose is in contact with hot walls (max. 50°C); · the hose is not under traction or tension and has no tight curves or twists; · the hose is not in contact with sharp objects or sharp corners; · if the hose is not perfectly airtight and leaks gas, do not try to repair it: replace it with a new hose; · verify that the hose is not past its expiry date (serigraphed on the hose itself). 8 Instructions for the installer CONNECTION USING RUBBER HOSES COMPLYING WITH THE CURRENT REGULATIONS IS ONLY PERMITTED IF THE HOSE CAN BE INSPECTED ALONG ITS ENTIRE LENGTH. THE TIGHTENING TORQUE BETWEEN CONNECTIONS THAT INCORPORATE A GASKET MUST NOT EXCEED 10NM 4. 5. 2 Connection to natural and city gas Make the gas connection using a rubber hose in accordance to the regulations in force (verify if the mark of such norm is printed on the tube). Accurately screw connector A to the gas tube B of the appliance ensuring to place gasket C in between. Place the rubber tube D on connector A and fix it with clip E conforming to the regulations in force. 9 Instructions for the installer 5. ADAPTATION TO DIFFERENT TYPES OF GAS Before carrying out the following operations, disconnect the appliance from the power supply. The appliance is preset for natural gas G20 (2H) at a pressure of 20 mbar. In the case of operation with other types of gas, the burner nozzles must be changed and the minimum flame adjusted on the gas taps. Extract the gas tap knob and turn the adjustment screw at the side of the tap rod until the correct minimum flame is achieved. Refit the knob and verify that the burner flame is stable (when turning the knob rapidly from the maximum to the minimum position the flame must not go out). Repeat the operation on all the gas taps. 13 Instructions for the user 7. THE CONTROL PANEL All the cooker controls are grouped together on the front panel. The symbols used are described in the table below. 55 50 45 40 35 30 5 10 15 20 25 MIN 150 175 275 200 225 250 TIMER KNOB 2-FUNCTION SELECTION KNOB GAS GRILL AND GAS OVEN THERMOSTAT KNOB FRONT LEFT-HAND BURNER KNOB REAR LEFT-HAND BURNER KNOB CENTRAL BURNER KNOB REAR RIGHT-HAND BURNER KNOB FRONT RIGHT-HAND BURNER KNOB HOB BURNERS CONTROL KNOB To light the flame, press the knob and turn it anticlockwise to the minimum flame symbol . To adjust the flame, turn the knob to the zone between the maximum ( ) settings. To turn off the burner, turn the knob to the position. ) and minimum ( TIMER KNOB In order to use the timer, the buzzer must be set by turning the knob in a clockwise direction. The numbers correspond to minutes (maximum 55 minutes). Adjustment is progressive and intermediate positions between the figures can be used. The end of cooking buzzer does not interrupt operation of the oven. GAS GRILL AND GAS OVEN THERMOSTAT KNOB This knob allows the gas burner and the gas grill inside the oven to be lit. [. . . ] If left to set for too long, they might damage the enamel lining of the oven. 11. 2 Cleaning the components of the hob 11. 2. 1 Racks Remove the racks and clean them with lukewarm water and non-abrasive detergent, making sure to remove any encrustations. Continuous contact between the racks and the flame can cause modifications to the enamel over time in those parts exposed to heat. This is a completely natural phenomenon which has no effect on the operation of this component. Warning: If using cast iron racks (optional, not supplied), at the end of cooking using pans with aluminium bases, you may find white residues on the racks. [. . . ]